Thermal Dynamics CUTMASTER 81 Скачать руководство пользователя | Manualshive

Страница: 36 / 88

background image

TROUBLESHOOTING

4-16

Manual 0-2957

7.

If a diode checks bad, replace the diode module.

8.

Reconnect all cables.

C. Diode Module Board Tests

WARNING

Disconnect primary power at the source before tak-
ing any resistance checks.

1. Input Diode Module Board Circuit Test

a.

Remove AC power. Refer to Appendix 5-A or 5-B,
Main PCB Wiring diagram.

b.

Check Input Diode for shorted input diode. With
an ohmmeter set on the diode range make the fol-
lowing checks from Main PC Board to Input Di-
ode:

For 400-Volt, 415-Volt, 460-Volt, and 600-Volt Power

Supplies:

Meter +

Meter -

Indication

E15

E1

Diode Drop

E1

E15

Open

E15

E2

Diode Drop

E2

E15

Open

E15

E3

Diode Drop

E3

E15

Open

E7

E1

Open

E1

E7

Diode Drop

E7

E2

Open

E2

E7

Diode Drop

E7

E3

Open

E3

E7

Diode Drop

E7

E15

Open

E15

E7

Diode Drop*

400V, 415V, 460V, and 600V

Input Diode Indications

* Indication can be twice

other indications.

For 208/230-Volt Power Supplies:

Meter (+)

Meter (-)

Indication

E7

E1

Open

E1

E7

Diode Drop

E15

E1

Diode Drop

E1

E15

Open

E15

E7

Diode Drop *

E7

E15

Open

208/230V Input Diode PCB

* Indication can be twice

other indications.

c.

The meter should indicate a diode drop in one di-
rection and an open in the other direction for each
check. Replace the Input Diode Module Board if
the readings do not match the chart.

d. If Input Diode Module Board is shorted, make the

following checks with an ohmmeter at the Main
Contactor (W1):

Meter (+)

Meter (-) Indication

L1

T1

Open

L2

T2

Open

L3

T3

Open

If any test has resistance, then replace the Main Con-
tactor.

2. Output Diode Module Board Circuit Test

a.

Use an ohmmeter set on the diode function and
make the following measurements on the Output
Diode Module Boards to Power Output PC Board.

Indication

Meter +

Meter - Meter + Meter -

E37

E58

E36

E57

Diode Drop *

E58

E37

E57

E36

Open

E37

E47

E36

E49

Diode Drop

E47

E37

E49

E36

Open

E58

E47

E57

E49

Open

E47

E58

E49

E57

Diode Drop

Output Diode A

Output Diode B

* Indication can be twice other indications.

b.

The meter should indicate a diode drop in one di-
rection and an open in the other direction for each
check. Replace the Output Diode Module Board(s)
if the readings do not match the chart.

«
...
34
35
36
37
38
...
»

Содержание CUTMASTER 81

























































































Отзывы:

Нет отзывов

Похожие инструкции для CUTMASTER 81

Бренд: Samsung Страницы: 70

Бренд: Samsung Страницы: 21

Бренд: Samsung Страницы: 28

Three-Phase Running Gear

Бренд: Miller Electric Страницы: 4

Бренд: jacarta Страницы: 4

FSA ECO SR-EFR BG

Бренд: Eco Страницы: 23

Бренд: FAAC Страницы: 4

Бренд: FAAC Страницы: 30

Бренд: M-Audio Страницы: 12

Бренд: HALDER Страницы: 7

Бренд: AI-Sonic Страницы: 8

Бренд: Akura Страницы: 11

Nexus Contractor SP-5NXC/T

Бренд: Speco Страницы: 4

Бренд: Sabiana Страницы: 56

DTS-212 SPEAKER SYSTEM

Бренд: Altec Lansing Страницы: 8

Бренд: Rotary Страницы: 16

Бренд: Air Liquide Страницы: 16

Бренд: Monacor Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды