Thermal Dynamics CUTMASTER 81 Скачать руководство пользователя

Страница: 26 / 88

TROUBLESHOOTING

4-6

Manual 0-2957

C. Fans do not operate; all control panel indicators OFF

1. Front Panel ON/OFF switch in OFF position

a. Place switch to ON (up) position.

2. Main power disconnect open

a. Close main power disconnect.

3. Torch is not properly connected to Power Supply.

a. Check torch connections to Power Supply.

Tighten or adjust as needed.

4. Shield cup not fully tightened on torch head.

a. Check shield cup for proper installation. Do

not overtighten.

5. Main power line fuses blown

a. Replace main power line fuses.

6. Improper input power cable connections inside Power

Supply

a. Refer to System Schematic and correct if needed.

7. Defective input power cable

a. Replace input power cable.

8. Fuse blown inside Power Supply

a. Replace internal Fuse per Subsection 5.06-A.

9. Line voltage above 10% tolerance (over voltage protec-

tion)

a. Reduce line supply.

10. Faulty Auxiliary Transformer (refer to Appendix pages,

28 VAC Circuit Diagram)

Measure for 28 VAC on Main PC Board from J23-1
to J23-3.

a. If voltage is not present, replace the Main PC

Board.

Main Printed Circuit Board Layout (logic board not shown)

Art # A-03651

INPUT
DIODE

E22

TP1

E15

TP4

J24

J32 J29

E10

E20

J30

E33

J18

J26

E27

J23

E30

J33

J31

E23

E32

J27

J25

IGBT A

IGBT B

J43

J34

J11

J15

J16

J17

FUSE

Содержание CUTMASTER 81

























































































Результаты поиска

Содержание CUTMASTER 81

Отзывы:

Похожие инструкции для CUTMASTER 81

Бренды по названию

Популярные бренды

Thermal Dynamics CUTMASTER 81, Руководство по обслуживанию

Результаты поиска

Содержание CUTMASTER 81

Отзывы:

Похожие инструкции для CUTMASTER 81

Бренды по названию

Популярные бренды