Theben RAM 712 KNX страница 15 Скачать руководство пользователя

Страница: 15 / 65

RAM 712 KNX

room thermostat for surface-mounted and flush-mounted installation

theben

Version: Dec-10 (subject to change) Page 15 of 65

•

Objects 11, 14 "Switching ON/OFF, priority, send value, temperature value, call/store
light scene, send, step / stop, height position , switching LED "

To use inputs E1 and E2 the external interface must be configured on the

settings,

parameter page

active

The function and type of object are dependent on

function of input

and

object type

parameters.

Table 8

Input function

Function

Description

Switch/key

Switching ON/OFF

Sends 1 bit switching commands in EIS 1

format

Priority

Sends priority telegram in 2 bit format

Send value

Sends a value between 0 and 255

Send temperature
value

Sends a temperature value in 2 byte format

Dimming

Switching ON/OFF

Switches dimmer on and off

Blinds

Step / stop

Sends 1 bit "UP" or "DOWN" telegrams.

Value

Valuator short/long

Sends 2 different 8 bit values depending on

length of time keystroks

Value for light
setting

Call/save light scene via 8 bit telegram

Valuator for blinds

Sends an 8 bit percentage value for positioning

blinds

Control LED

Receives 1 bit telegram for controlling LED

•

Objects 12, 15 "Brighter, darker, brighter/ darker, UP, DOWN, UP/DOWN, slat
position"

The function and the type of object also depend on

input function

parameter.

Table 9

Input function

Function

Description

Switch/key

Not available

Dimming

Brighter , darker

Brighter / darker

4 bit dimming commands for the dimming
actuator in EIS 4 format

Blinds

UP, DOWN,
UP/DOWN

1 bit motion commands for the blinds actuator
in EIS 7 format

Value for blinds

Slat position

Sends 1 byte telegram for positioning slats

Control LED

Not available

Содержание RAM 712 KNX


































































Результаты поиска

Содержание RAM 712 KNX

Отзывы:

Похожие инструкции для RAM 712 KNX

Бренды по названию

Популярные бренды

Theben RAM 712 KNX, Руководство пользователя

Результаты поиска

Содержание RAM 712 KNX

Отзывы:

Похожие инструкции для RAM 712 KNX

Бренды по названию

Популярные бренды