Theben RAM 712 KNX страница 33 Скачать руководство пользователя

Страница: 33 / 65

RAM 712 KNX

room thermostat for surface-mounted and flush-mounted installation

theben

Version: Dec-10 (subject to change) Page 33 of 65

Continuation:

Designation

Values

Description

Response after
restoration of the bus
supply

None

No response.

Update

The current status of the channel is
sent.

Same as after rising edge

Response configured as for rising
edge.

Same as after falling edge

Response configured as for falling
edge.

Update after 5 sec.

Update after 10 sec.
Update after 15 sec.

The current channel status is sent
after set time has elapsed.

After 5 sec. same as after

rising edge

After 10 sec. same as after

rising edge

After 15 sec. same as after

rising edge

Once the set time has elapsed the
channel responds as configured for a
rising edge.

After 5 sec. same as after

falling edge

After 10 sec. same as after

falling edge

After 15 sec. same as after

falling edge

Once the set time has elapsed the
channel responds as configured for a
falling edge.

Содержание RAM 712 KNX


































































Результаты поиска

Содержание RAM 712 KNX

Отзывы:

Похожие инструкции для RAM 712 KNX

Бренды по названию

Популярные бренды

Theben RAM 712 KNX, Руководство пользователя

Результаты поиска

Содержание RAM 712 KNX

Отзывы:

Похожие инструкции для RAM 712 KNX

Бренды по названию

Популярные бренды