The Fire Brick D95 Скачать руководство пользователя страница 40

Страница: 40 / 47

8. Installing the Standard Flue

9A: INSTALL THE FLUE

Place the flue cowling (hat) on the plain end of the

flue pipe, this is meant to be a snug, tight fit.

Now, fit the crimped end of the flue pipe section into

the stainless steel sleeve protruding from the flue

Gallery. Remove the plastic film from the stainless

steel ring that covers the flue expansion joint.

9B: SECURE PIPE FOR WINDY AREAS

The flue is quite stable with only one length but if

you live in a particularly windy area you may want

to secure your flue using stainless steel screws or

pop rivets (screws if you intend to remove the flue in

future). With either method you will have to pre-drill

the holes.

If you use three screws/rivets at equal spacing around

the flue, this will be sufficient to hold it level.

If you’ve built your oven outdoors and the flue will be well clear of any combustible materials as per the diagram

on page 9, you can install the standard flue for the oven following the steps detailed below.

This is important, if you go down the path of installing your own flue system and somehow, your oven causes

a catastrophic fire, your home insurance may be null and void. Put this in the same category as working with

high voltage electricity - the risks massively outweigh the rewards. Don’t risk it, use a licensed plumber.

You may want to change the colour of the flue - let’s say you wanted it black, for example. Don’t try to paint

the stainless steel flue - there is no paint available that can withstand the full range of temperature that this

flue can reach. Rather, get a ‘twin-skin’ flue system, and have the external flue pipe (the second ‘skin’) painted

in a high temp coating. This will also require you to purchase a ‘twin-skin’ cowling to lock the two flue pipes

together at the top. These flue systems and other, more complex flues are available at good plumbing supply

stores, and most wood heater retailers. Your plumber will source these components for you.

The flue should be installed whenever the oven is fired. Without the flue, most of the smoke will come out of the

oven mouth and cover your brickwork with soot. Leave the flue installed unless the oven is being covered for a

long period of time (eg. to protect the oven from freeze-thaw during winter in a very cold climate).

If your installation involves anything more complex than the basic setup that we provide in

the kit, you must engage a suitably qualified plumber to supply and install the flue for you.

Your local fireplace store will have several professionals they can recommend. Your oven can

reach

extreme

temperatures, to the point where the flue glows orange.

Installing the Standard Flue

Содержание D95
















































Результаты поиска

Содержание D95

Отзывы:

Похожие инструкции для D95

Бренды по названию

Популярные бренды

The Fire Brick D95, Инструкция пользователя

Результаты поиска

Содержание D95

Отзывы:

Похожие инструкции для D95

Бренды по названию

Популярные бренды