Teyme EOLO-GTE10 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 52

Teyme EOLO-GTE10 Скачать руководство пользователя страница 37

6. Working

37

4.

Connect the PTO to the planned working revolutions.

5.

Place the switches 1 and 2 in ON mode (upper position – turned on leds)

6.

Turn the pessure knob (B) to the higuest desired pressure. Clockwise turn stands for
increasing pressure, counterclockwise for diminishing pressure.

7.

Close the sector 1 (left).

8.

Turn the knob of the regulator of the self-
compensated system (A) of the closed sector
(left) until achieving the marked pressure with
both sectors open.

9.

Open again the sector and repeat the
operation closing and compensating the right
sector.

10.

Open both sectors and adjust the desired

pressure with the pressure switch.

6.5.3.2.

Working

It has the same functions than system 1, besides pressure regulation by means of an electrical valve (C) and
an added selector in the control box.

6.5.4.

System 3 Electrical Distributor

6.5.4.1.

Pressure and Self-compensating System Adjustment

1.

With the PTO disconnected set the switches 1 and 2 (5) or the general (6) of the control in OFF
(lower position – turned off leds).

2.

Keep the pressure switch (7) activated downwards for 5 seconds in order to suppress the
pressure of the electrical regulator.

3.

Turn the knobs of the regulators of self-compensated system (A) in open mode (0 position).

4.

Connect the PTO to the planned working revolutions.

5.

Set the switches 1, 2 and the general in ON (upper position – turned on leds).

6.

Turn the knob of pressure (B) to the highest desired pressure, Clockwise turn stands for increasing
pressure, counterclockwise for diminishing pressure.

7.

Close sector 1 (left).

8.

Turn the knob of the regulator of self-compensating system (A) of the closed sector (left) until
reaching the attained pressure with both sectors open.

9.

Open again the sector and repeat the operation closing and compensating sector 2.

10. Open the two sectors or/and the general and adjust the desired pressure with the pressure

switch.

6.5.4.2.

Working

With the same functions than system 2, with an added electrovalve which allows the opening or the
closing of general circuit by means of a selector added to the control box. Light indicator is included. There
is the possibility of replacing the control box by a wireless control with identical fonctions. See “Quick guide
of working of wireless control” in the following page.

«
...
35
36
37
38
39
...
»

Содержание EOLO-GTE10





















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды