Teyme EOLO-GTE10 страница 28 Скачать руководство пользователя | Manualshive

Страница: 28 / 52

background image

28

5. Adjustments and How to Start Up
tart up

5.

Cut with a saw both parts of the shaft on the marked area leaving the same size of tube in
both sides. Afterwards, polish all tubes to leave out all the burrs.

6.

Check out that the ends of the tubes do not bump into the knots when the tractor turns in the narrowest
angle.

7.

Check that the tubes of the PTO shaft remain attached in at least a 60% of their working length
with the machine and the tracto levelled and lined up as it is described in the picture:

8.

Grease the tubes and assemble again the PTO shaft to the tractor and to the machine.

DANGER! Remember that all knots in the tractor and in the machine, as well as the
PTO shaft, must be perfectly protected; in case of accident the user is the only
responsible if the machine has not the adequate protections in perfect conditions of
maintenance.

5.4.

Tyres

There is a range of exchangeable wheels to work in plots with different conditions. Check with
TEYME the conditions of the land plot to get recommendations about the wheels to be used.
The wheels of the machines must always have the correct pressure, since these act as a suspension
method with the full tank. It must be controlled the pressure of these in cold and through the valve.

Keep always the recommended pressure for a durability and normal wear of the tyres of the machine,
thus avoiding the punctures and unnecessary efforts.

Tyres

Recommended inflating pressure

(bar)

260/80-12”

4

260/75-15.3”

3,6

260/70-15.3”

3,6

300/80-15,3”

2,8

340/55-16”

4

Tyre

Recommended inflating pressure

(bar)

340/65-18”

4

400/60 15,5”

3,6

400/55-17”

3,6

500/50-17”

2,8

«
...
26
27
28
29
30
...
»

Содержание EOLO-GTE10





















































Отзывы:

Нет отзывов

Похожие инструкции для EOLO-GTE10

Бренд: GALLERY Страницы: 18

Бренд: Ecco Страницы: 4

Бренд: JD Squared Страницы: 15

Бренд: DAPAudio Страницы: 16

Бренд: 3M Страницы: 28

Бренд: Jacobsen Страницы: 6

Бренд: Califone Страницы: 7

Бренд: CALITEK Страницы: 16

Бренд: LAHTI PRO Страницы: 20

Бренд: LAHTI PRO Страницы: 16

Бренд: J&M Страницы: 53

Бренд: Qazqa Страницы: 2

Aspect Q-CARD 100-4T

Бренд: idi Страницы: 38

Бренд: JBL Страницы: 38

Бренд: JBSYSTEMS Light Страницы: 32

Бренд: JBM Страницы: 12

Бренд: Samson Страницы: 2

Бренд: York Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды