Texas Instruments TMS320x281 series Скачать руководство пользователя | Manualshive

Страница: 39 / 84

background image

2.11.1 CAN Module Action in SUSPEND

www.ti.com

Master Control Register (CANMC)

1. If there is no traffic on the CAN bus and SUSPEND mode is requested, the node goes into SUSPEND

mode.

2. If there is traffic on the CAN bus and SUSPEND mode is requested, the node goes into SUSPEND

mode when the ongoing frame is over.

3. If the node was transmitting, when SUSPEND is requested, it goes to SUSPEND state after it gets the

acknowledgment. If it does not get an acknowledgment or if there are some other errors, it transmits an
error frame and then goes to SUSPEND state. The TEC is modified accordingly. In the second case,
i.e., it is suspended after transmitting an error frame, the node re-transmits the original frame after
coming out of suspended state. The TEC is modified after transmission of the frame accordingly.

4. If the node was receiving, when SUSPEND is requested, it goes to SUSPEND state after transmitting

the acknowledgment bit. If there is any error, the node sends an error frame and go to SUSPEND
state. The REC is modified accordingly before going to SUSPEND state.

5. If there is no traffic on the CAN bus and SUSPEND removal is requested, the node comes out of

SUSPEND state.

6. If there is traffic on the CAN bus and SUSPEND removal is requested, the node comes out after the

bus goes to idle. Therefore, a node does not receive any "partial" frame, which could lead to
generation of error frames.

7. When the node is suspended, it does not participate in transmitting or receiving any data. Thus neither

acknowledgment bit nor any error frame is sent. TEC and REC are not modified during SUSPEND
state.

SPRU074F – May 2002 – Revised January 2009

eCAN Registers

39

Submit Documentation Feedback

«
...
37
38
39
40
41
...
»

Содержание TMS320x281 series





















































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320x281 series

Бренд: Gardigo Страницы: 8

Бренд: Gardigo Страницы: 19

Бренд: GBD Страницы: 15

Бренд: Jäger Страницы: 50

Бренд: LANGER EMV-Technik Страницы: 48

Бренд: VAT Страницы: 26

Бренд: We Care Solar Страницы: 46

Бренд: Watts Страницы: 4

OneFlow OFTWH-R

Бренд: Watts Страницы: 8

Бренд: Watts Страницы: 8

Бренд: Zeta Страницы: 44

KOOL STRIDE KS-S

Бренд: KOOL-STOP Страницы: 8

Бренд: Game ready Страницы: 24

Бренд: Simplex Страницы: 40

Бренд: Lauda Страницы: 40

Бренд: Adaptec Страницы: 2

Бренд: Webasto Страницы: 12

Бренд: SMC Networks Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды