manualshive.com logo in svg

Texas Instruments CC2533, Руководство пользователя

Поделиться
Скачать
Texas Instruments CC2533 Скачать руководство пользователя страница 194

Endpoint-0 Interrupts

www.ti.com

21.6.1 Error Conditions

When a protocol error occurs, the USB controller sends a STALL handshake. The

USBCS0.SENT_STALL

bit is asserted, and an interrupt request is generated if the endpoint-0 interrupt is properly enabled. A
protocol error can be any of the following:

•

An OUT token is received after

USBCS0.DATA_END

has been set to complete the OUT data stage (the

host tries to send more data than expected).

•

An IN token is received after

USBCS0.DATA_END

has been set to complete the IN data stage (the host

tries to receive more data than expected).

•

The USB host tries to send a packet that exceeds the maximum packet size during the OUT data
stage.

•

The size of the DATA1 packet received during the status stage is not 0.

The firmware can also terminate the current transaction by setting the

USBCS0.SEND_STALL

bit to 1. The

USB controller then sends a STALL handshake in response to the next request from the USB host.

If an EP0 interrupt is caused by the assertion of the

USBCS0.SENT_STALL

bit, this bit should be

de-asserted, and firmware should consider the transfer as aborted (and consequently free the memory
buffers, etc.).

If EP0 receives an unexpected token during the data stage, the

USBCS0.SETUP_END

bit is asserted, and

an EP0 interrupt is generated (if enabled properly). EP0 then switches to the IDLE state. Firmware should
then set the

USBCS0.CLR_SETUP_END

bit to 1 and abort the current transfer. If

USBCS0.OUTPKT_RDY

is

asserted, this indicates that another setup packet has been received that firmware should process.

21.6.2 SETUP Transactions (IDLE State)

The control transfer consists of two or three stages of transactions (setup

–

data

–

status or setup

–

status). The first transaction is a setup transaction. A successful setup transaction comprises three
sequential packets (a token packet, a data packet, and a handshake packet), where the data field
(payload) of the data packet is exactly 8 bytes long and is referred to as the setup packet. In the setup
stage of a control transfer, EP0 is in the IDLE state. The USB controller rejects the data packet if the
setup packet is not 8 bytes. Also, the USB controller examines the contents of the setup packet to
determine whether or not there is a data stage in the control transfer. If there is a data stage, EP0
switches state to TX (IN transaction) or RX (OUT transaction) when the

USBCS0.CLR_OUTPKT_RDY

bit is

set to 1 (if

USBCS0.DATA_END = 0

).

When a packet is received, the

USBCS0.OUTPKT_RDY

bit is asserted and an interrupt request is

generated (EP0 interrupt) if the interrupt has been enabled. Firmware should perform the following when a
setup packet has been received:

1. Unload the setup packet from the EP0 FIFO

2. Examine the contents and perform the appropriate operations

3. Set the

USBCS0.CLR_OUTPKT_RDY

bit to 1. This denotes the end of the setup stage. If the control

transfer has no data stage, the

USBCS0.DATA_END

bit must also be set. If there is no data stage, the

USB controller stays in the IDLE state.

21.6.3 IN Transactions (TX State)

If the control transfer requires data to be sent to the host, the setup stage is followed by one or more IN
transactions in the data stage. In this case, the USB controller is in the TX state and only accepts IN
tokens. A successful IN transaction comprises two or three sequential packets (a token packet, a data
packet, and a handshake packet

(1)

). If more than 32 bytes (maximum packet size) is to be sent, the data

must be split into a number of 32-byte packets followed by a residual packet. If the number of bytes to
send is a multiple of 32, the residual packet is a zero-length data packet, because a packet size less than
32 bytes denotes the end of the transfer.

Firmware should load the EP0 FIFO with the first data packet and set the

USBCS0.INPKT_RDY

bit as

(1)

For isochronous transfers there would not be a handshake packet from the host.

194

USB Controller

SWRU191C

–

April 2009

–

Revised January 2012

Submit Documentation Feedback

Copyright

©

2009

–

2012, Texas Instruments Incorporated

Содержание CC2533



















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды