Texas Instruments CC2533 Скачать руководство пользователя страница 157

Страница: 157 / 370

www.ti.com

AES Interrupts

Message Decryption

CCM Mode Decryption

In the coprocessor, the automatic generation of CTR works on 32 bits; therefore, the maximum length of a
message is 128

bits, that is 2

bytes, which can be written in a 6-bit word. So, the value L is set to 6.

To decrypt a CCM-mode processed message, the following sequence can be conducted (key is already
loaded).

Message Parsing Phase

1. The software parses the message by separating the M rightmost octets, namely U, and the other

octets, namely string C.

2. C is padded with zeros until it can fill an integral number of 128-bit blocks.

3. U is padded with zeros until it can fill a 128-bit block.

4. The software creates the key stream block A0. It is done the same way as for CCM encryption.

5. The software loads A0 by selecting a Load IV/nonce command. To do so, it sets the mode to CFB or

OFB at the same time as it selects the IV load.

6. The software calls a CFB or an OFB encryption on the encrypted authenticated data U. The uploaded

buffer contents stay unchanged (M = 16), or only its first M bytes stay unchanged, the others being set
to 0 (M != 16). The result is T.

7. The software calls a CTR-mode decryption immediately on the encrypted message blocks C.

Reloading the IV/CTR is not necessary.

Reference Authentication Tag Generation

This phase is identical to the authentication phase of CCM encryption. The only difference is that the
result is named MACTag (instead of T).

Message Authentication Checking Phase

The software compares T with MACTag.

15.8 AES Interrupts

The AES interrupt, ENC, is produced when encryption or decryption of a block is completed. The interrupt
enable bit is

IEN0.ENCIE,

and the interrupt flag is

S0CON.ENCIF

15.9 AES DMA Triggers

Two DMA triggers are associated with the AES coprocessor. These are ENC_DW, which is active when
input data must be downloaded to the

ENCDI

must be uploaded from the

ENCDO

The

ENCDI

and

ENCDO

registers should be set as destination and source locations for DMA channels

used to transfer data to or from the AES coprocessor.

15.10 AES Registers

The AES coprocessor registers have the layout shown in this section.

The registers return to their reset value when the chip enters PM2 or PM3.

157

SWRU191C

–

April 2009

–

Revised January 2012

AES Coprocessor

Submit Documentation Feedback

2009

–

2012, Texas Instruments Incorporated

Содержание CC2533

































































































































































































































































































































































Результаты поиска

Содержание CC2533

Отзывы:

Бренды по названию

Популярные бренды

Texas Instruments CC2533, Руководство пользователя

Результаты поиска

Содержание CC2533

Отзывы:

Бренды по названию

Популярные бренды