TESVOLT TS HV 70 Скачать руководство пользователя страница 18

Страница: 18 / 57

battery storage system ts hV 70 outdoor

07/2020

5.6 CONNECTIONS AND STRUCTURE OF THE APU HV1000-S

NO . DESIGNATION

DESCRIPTION

BATTERY -

The battery’s DC connection for the negative pole (black)

The battery’s DC connection for the positive pole (red)

24 V AUX PWR

Connection not used on the TS HV 70 Outdoor.

E-STOP

Two-pin plug for the optional connection of a fl oating emergency stop switch for quick shutdown
(pre-installed with the bridge on delivery)

TERM

CAN bus termination
TERM must be activated (ON) for the fi rst and last CAN bus participants.

CAN IN

APU HV1000-S master/slave communication (input)

CAN OUT

APU HV1000-S master/slave communication (output)

CAN SMA

Connection not used on the TS HV 70 Outdoor.

LAN

Modbus TCP/IP transmission for communication between the battery and SMA Inverter Manager

ADDRESS

Further information can be found in the section “Overview of all addressing options” on page 49.

BAT COM

Communication connection to the fi rst battery module

DC connection for the SMA STPS 60 or BatBreaker for the positive pole (red)

CHARGER -

DC connection for the SMA STPS 60 or BatBreaker for the negative pole (black)

GROUND

Grounding connection (M6 thread bolt on the rear of the unit)

DISPLAY

Display interface

MARKING

Marking for activating and changing the display by tapping

SWITCH

ON/OFF switch for the battery

APU Fuse (F1)

Fuse to protect the APU HV1000-S (2 A miniature fuse, 5 x 20 mm, time lag (T) according to
DIN 41571-2, type: ESKA 521.020, 250 V

). Operation is not possible with a defective fuse.

5.7 CONNECTIONS AND STRUCTURE OF THE BATTERY MODULES

NO. DESIGNATION

DESCRIPTION

– POL

Battery negative pole (black)

+ POL

Battery positive pole (red)

RACK BALANCING IN

Rack balancing (input)

RACK BALANCING OUT

Rack balancing (output)

BAT COM OUT

Communication connection to
battery module (output)

BAT COM IN

Communication connection to
battery module (input)

BATTERY

CHARGER

21
22

Содержание TS HV 70


























































Результаты поиска

Содержание TS HV 70

Отзывы:

Похожие инструкции для TS HV 70

Бренды по названию

Популярные бренды

TESVOLT TS HV 70, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TS HV 70

Отзывы:

Похожие инструкции для TS HV 70

Бренды по названию

Популярные бренды