Teseq NSG 3000A Series Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 157

background image

AMETEK CTS

NSG 3040A, 3060A series

Operating Manual

V 1.04

51 / 157

6.5.

EUT Setup

In the EUT setting the user specified his EUT. With this information the generator software will configure all
settings to the EUT requirements.

The user defines:

-  Mode of supply voltage (AC/DC)
-  Configuration of the EUT supply wiring
-  Default channel for the power supply
-  The mains supply voltage

Advantages are:

-  Select only set the possible couplings and hides all unnecessary settings for the user
-  Filters the standard tests adapted to the EUT like AC 50Hz, AC 60 Hz, DC.
-  Set the VAR 3005A-S16 to the settled nominal voltage

Select EUT setting menu

Figure below shows to enter the EUT setting menu

EUT Setup

The generator uses the settings and offers exact the needed
information for the EUT. All needless information will not be
displayed



EUT Configuration and Setup for the test.



EUT and Supply path and mains voltage configuration



EUT current and voltage limit

«
...
49
50
51
52
53
...
»

Содержание NSG 3000A Series






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для NSG 3000A Series

Бренд: Keithley Страницы: 36

Бренд: Rain-Flo Irrigation Страницы: 16

FX-ARM CONTROLLER

Бренд: Magicfx Страницы: 16

Бренд: NEILPRYDE Страницы: 53

Бренд: JAC Страницы: 103

Бренд: 3Disc Страницы: 12

Бренд: Rapid Technic Страницы: 152

Бренд: dbx Страницы: 12

Бренд: dbx Страницы: 13

Бренд: dbx Страницы: 72

Бренд: dbx Страницы: 11

Бренд: dbx Страницы: 16

PORTABLE ICE FISHING KIT

Бренд: Garmin Страницы: 5

Бренд: JBL Страницы: 38

Бренд: JBSYSTEMS Light Страницы: 32

Бренд: JBM Страницы: 12

Бренд: Raytheon Страницы: 68

Бренд: KegLand Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды