manualshive.com logo in svg

Terex AL4L, Руководство по обслуживанию

Поделиться
Скачать
Terex AL4L Скачать руководство пользователя страница 39

REV B

 Section 3 • Scheduled Maintenance Procedures

August 2016

Part No. 229171 

AL4L • AL5L 

3 - 25

D-1
Perform Engine Maintenance -
Kubota D1105-D3BG Models

     

     

Engine specifi cations require that this procedure 
be performed every 1500 hours or bi-annually, 
whichever comes fi rst.

• Injectors

Required maintenance procedures and additional 
engine information is available in the 

Kubota

D1105 Operators Manual

 (Kubota part number 

16622-89166)

Kubota D1105 Operators Manual

Genie part number 

 

131379

D-2
Perform Coupler Maintenance

     

     

Coupler specifi cations require that this procedure 
be performed annually.

Maintaining the coupler in good condition is 
essential to safe operation and good performance. 
Coupler failure could result in a machine tip-over 
during transport, and component damage may 
also result if problems are not discovered and 
repaired in a timely fashion.

1  Check coupler welds and mounting bolt torque. 

Torque the fasteners to 35 ft-lbs / 48 Nm.

  Result: 1.5 full threads of the locking bolt must 

be exposed beyond the lock nut after the 
adjustment.

2  Apply automotive grease to the coupler ball 

pocket.

3  Oil coupler pivot points using SAE 30 motor oil.

Checklist D Procedures

Содержание AL4L




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды