Terex AL4L Скачать руководство пользователя страница 23

Страница: 23 / 67

REV B

Section 3 • Scheduled Maintenance Procedures

August 2016

Part No. 229171

AL4L • AL5L

3 - 9

A-10
Perform Engine Maintenance -
Kubota D1105-D3BG Models

Engine specifi cations require that this procedure
be performed every 100 hours or quarterly,
whichever comes fi rst.

• Fuel lines and clamps

Required maintenance procedures and additional
engine information is available in the

Kubota

D1105 Operators Manual

(Kubota part number

16622-89166)

Kubota D1105 Operators Manual

Genie part number

131379

5 Visually inspect the winch cable for the

following:

• nicks (partial strand cut through)

• kinks in the cable (permanent bends)

• weld spatter

Result: Nicks, kinks in the cable or weld spatter

are found. The cable must immediately be
replaced.

6 Visually inspect the winch cable for the

following:

· crushed spot on the cable

Result: A crushed spot on the cable measuring

125% of the cable diameter or more is found
OR there is a broken wire at the crush point.
The cable must immediately be replaced.

7 Wind the cable onto the winch, ensuring that

the cable is correctly installed onto each of the
pulleys.

CHECKLIST A PROCEDURES

Содержание AL4L




































































Результаты поиска

Содержание AL4L

Отзывы:

Бренды по названию

Популярные бренды

Terex AL4L, Руководство по обслуживанию

Результаты поиска

Содержание AL4L

Отзывы:

Бренды по названию

Популярные бренды