manualshive.com logo in svg

Terex AL4L, Руководство по обслуживанию

Поделиться
Скачать
Terex AL4L Скачать руководство пользователя страница 24

REV B

August 2016

3 - 10 

AL4L • AL5L 

Part No. 229171

Section 3 • Scheduled Maintenance Procedures

A-11
Perform Lighting-battery 
Maintenance (if equipped)

     

     

Terex specifi cations require that this procedure be 
performed for the batteries which supply power to 
the lighting every 160 hours or monthly, whichever 
comes fi rst.

Proper battery condition is essential to good 
machine performance and operational safety. 
Improper fl uid levels can result in component 
damage and hazardous conditions.

WARNING

 Electrocution/burn hazard. 

Contact with electrically charged 
circuits could result in death or 
serious injury. Remove all rings, 
watches and other jewelry.

WARNING

  Bodily injury hazard. Batteries 

contain acid. Avoid spilling or 
contacting battery acid. Neutralize 
battery acid spills with baking 
soda and water.

1  Open the cabinet doors.

2  Check the battery acid level. If needed, 

replenish with distilled water to 

1

/

8

 inch / 3 mm 

below the bottom of the battery fi ll tube. Do not 
overfi ll.

3  Install the vent caps and neutralize any 

electrolyte that may have spilled.

A-12
Perform Engine Maintenance -
Kubota D1105-D3BG Models

     

     

Engine specifi cations require that this procedure 
be performed every 200 hours or quarterly, 
whichever comes fi rst.

• Radiator hoses and clamps
• Intake air piping
• Change engine oil

Required maintenance procedures and additional 
engine information is available in the 

Kubota

D1105 Operators Manual

 (Kubota part number 

16622-89166)

Kubota D1105 Operators Manual

Genie part number 

 

131379

CHECKLIST A PROCEDURES

Содержание AL4L




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды