background image

August 2016

Section 4 • Repair Procedures

4 - 2 

AL4 • AL4000 

Part No. 218567

1-1
Mast

How to Remove the Mast 
Assembly

WARNING

  Bodily injury hazard. The 

procedures in this section 
require specifi c repair skills, 
lifting equipment and a suitable 
workshop. Attempting this 
procedure without these skills 
and tools could result in death 
or serious injury and signifi cant 
component damage. Dealer 
service is required.

1  Turn the handle of the mast winch and fully 

loosen the mast cable.

2  Open the cabinet doors and locate the winch. 

Remove the cable retaining fastener securing 
the cable to the winch drum. Unwind the cable 
from the winch drum.

CAUTION

  Bodily injury hazard. Cables can 

fray. Always wear adequate hand 
protection when handling the 
cable.

3  Remove the fasteners securing the coil cable 

cover onto the side of the mast. Set the cover 
and fasteners to the side, and lay the coil cable 
to the side.

4  Tag and disconnect the light heads from the 

mast junction box, and remove the light heads 
from the mast.

5  Remove the light head mount from the top of 

the mast.

6  Remove the junction box from the top of the 

mast. Lay the coil cord and junction box to the 
side.

7  Attach a lifting strap from an overhead crane to 

the mast. Support the mast. Do not apply any 
lifting pressure.

8  Unlock the mast hold-down pin at the mast 

cradle.

9  Remove the mast pivot pin fasteners, securing 

the lower end of the mast to the machine, and 
remove the mast from the machine.

mast pivot pin

Mast

a

Discount-Equipment.com

Содержание AL4

























































































Отзывы: