manualshive.com logo in svg

Teracue ENC-200, Руководство пользователя

Поделиться
Скачать
Teracue ENC-200 Скачать руководство пользователя страница 9

ENC-200™ H.264 Encoder 
User Guide V1.8 

 

9

 

2.3 

Connecting the Encoder (FR-110 chassis) 

 
Please pay attention about the cabling order between the power supply and the FR-chassis. Connect 
at first always the connector of the power supply to the FR-chassis.  
 
The cable connector can be locked to the socket of the encoder, so the cable cannot accidentally be 
pulled out [Bayonet Socket]. To do so the connector has to be placed on the socket and lightly turned 
90° in a clockwise motion. 
 
After you have connected the connector of the power supply to the chassis, please connect the power 
cable to the power supply. 
 
As next, please connect the network cable to the network interface and connect your video source unit 
to  the  video  input  of  the  ENC-200™.  Concerning  of  the  video  input  you  have  the  choice  between 
different  video  signal  types.  The  ENC-200™  supports  SDI  (with  embedded  audio),  Composite,  S-
Video, YP

b

P

r

 signals. If you have a Composite (CVBS), S-Video (YC) or a YP

b

P

r

 signal, please use the 

Sub-D 26-pin connector via the breakout cable. If you have a SDI or Composite signal, please use the 
BNC connector.  
 
Furthermore, if you have analogue audio, please use the Sub-D 26-pin connector via breakout cable. 
 

Figure 1: ENC-200™ front side 

 

Front panel connection: 

Description: 

Network: 

Standard 10/100Mbit/s Ethernet via RJ-45 

USB: 

USB-interface. 

Video Audio Comport GPIO: 

Audio-,  Video-  and  Data  Output/Input  for  Composite,  S-Video, 
YP

b

P

r

,  Audio-In,  Audio-Out,  GPIO,  AES-In,  RS-232,  Genlock-In, 

via Sub-D 26 pin interface. 

Video: 

Video  Input  for  Composite  or  SDI  (with  embedded  Audio)  via 
BNC interface. 

LED: 

LED  status  indicator.  The  LED  indicates  the  status  (operational 
state)  of  the  ENC-200  encoder.  The  status  is  indicated  by  the 
LED colour and LED flashing (blinking) speed. 

 

 

LED status: 

Description: 

Constant green:  OK, encoder in operation, encoding video. 
Flashing green: 

OK, but video input signal is missing. 

Flashing red: 

Network  error.  Encoder  can  not  send  data 
packets. 

Constant red: 

General error. 

No LED light: 

Check power and power supply. 

Power supply connector:  

Cable connector for the power supply. 

Table 1: Description of the connectors on the ENC-200™ front side 

 
 
 
 
 

 

 

 

 

 

 

CVBS = FBAS = Composite Signal 
YC = S-Video Signal 

Содержание ENC-200




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды