manualshive.com logo in svg

Teracue ENC-200, Руководство пользователя

Поделиться
Скачать
Teracue ENC-200 Скачать руководство пользователя страница 23

ENC-200™ H.264 Encoder 
User Guide V1.8 

 

23

 

3.4.5 

Menu: Encoder / Destination 

 
ENC-200™ is capable to encode a video either as a unicast stream or a multicast stream. According 
to the entered destination IP-address, the encoder will automatically recognize whether it should be a 
unicast or multicast stream. 
 
Figure 10 shows the ‘Encoder / Destination’ page of the ENC-200™ encoder.  
 

Figure 10: ‘Encoder / Destination’ page of the ENC-200™ encoder 

 
Table 10 describes the ‘Encoder / Destination’ page of the ENC-200™. 
 

Settings: 

Description: 

Transport Protocol: 

Shows the used transport protocol, which can be changed in the 
ENCODER > SETTINGS webpage of ENC-200™. (Read only) 

IP address: 

Specifies the destination IP-address which should the ENC-200™ 
use for the encoded video. 
If you want to stream a multicast stream: 
Please  enter  in  the  ‘IP  address’  field  your  desired  multicast  IP-
address, e. g. 239.252.20.100. 
If you want to stream a unicast stream:  
Enter in the ‘IP address’ field the IP-address of the destination, e. 
g. the IP-address of the DEC-200™, see Figure 11. 

Port: 

Specifies  the  port  on  which  the  encoder  shall  stream  the  video. 
Enter in this field the port number which shall the stream has. 

Source Port: 

Specifies  the  port  number  of  the  source  in  the  UDP/TCP 
datagram.  You  can  set  the  source  port  to  static  port  number 
which is entered manually. Or you can set the source port to port 
number which is set automatically by the encoder. As default the 
source port is set to 9200. The automatically mode can be set by 
entering the value ‘0’ in the text field and by confirming this entry 
with the 'APPLY' button. 

.!. 

If  you  change  the  ‘source  port’  manually,  please  be 

 

sure,  that  your  entered  port  number  is  smaller  than 

 

1024 and higher than 9200, because in the range from 

 

1024 and 9200 there are some reserved and used port 

 

numbers.  For  example  GPIO  uses  the  port  number 

 

7778  and  the  comport  7777.  Talkback  uses  the  port 

 

number 9177 and SNMP and SAP uses also reserved 

 

port numbers. 

Содержание ENC-200




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды