manualshive.com logo in svg

Teracue ENC-200, Руководство пользователя

Поделиться
Скачать
Teracue ENC-200 Скачать руководство пользователя страница 4

ENC-200™ H.264 Encoder 
User Guide V1.8 

 

4

 

II.  Release Notes 

 
Following are the Features listed which are supported from the firmware versions: 
 
Version 0.9.13 

– 

10/15/2009  10:54 

 

Unicast and Multicast streaming is supported. 

 

Support of PAL and NTSC. 

 

CVBS Video Input is supported by using the breakout cable.  

 

CVBS Video Input is supported by using the BNC interface on the front panel. 

 

YC Video Input is supported. 

 

SDI Video Input is supported by using the BNC interface on the front panel. 

 

SDI embedded Audio is supported. 

 

Analogue Audio Input with microphone level is supported. 

 

Analogue Audio Input with line level is supported. 

 

AES input is supported. 

 

Transmission of H.264 SD (MPEG-4 part 10) streams is possible. 

 

Deinterlacing is supported. 

 

Simple firmware updating via web interface. 

 

Real Time Clock (RTC) support. 

 

DHCP Support. 

 

Network settings are adjustable. 

 

Overview  of  the  ENC’s  system  environments  displayed  under  ‘System’  menu,  i.e.  encoder 
uptime, firmware version. 

 

Support of the Factory-Reset feature via jumper. 

 
 
Version 0.9.15 

– 

11/03/2009  08:51 

 

Page refresh of the ENC web pages are supported 

 

New default settings e.g.: IP 172.16.20.100, Destination IP 239.252.20.100. 

 

XPlayer-Link  added.  For  viewing  and  monitoring  of  the  ENC-200  Stream.  If  the  Standalone 
XPlayer  is installed  on the  client  PC, running the  web-config pages, the XPlayer can directly 
be launched by a mouse click from the user interface. 

 
Version 0.9.16 

– 

11/18/2009  12:36 

 

Improvement of the NTSC support 

       
 
Version 0.9.21 

– 

04/30/2010  11:06 

 

COM server added. 

 

GPIO function is added; GPIO Modes: Manual, Passthrough/A, Passthrough/B. 

 

Added support for Status LED. 

 

‘VideoLoss’ mode is added. Users can enable the ‘VideoLoss’ mode to stream a frame, when 
the encoder loses the input video. (Only for analogue input) 

 

Comport for RS-232 operation is supported and settings are adjustable via GUI. 

 

New Comport Mode ‘Packet’ is added for a tunnelled data transmission with the compliance of 
the temporal sequence. 

 

New setting options in the encoder/audio settings menu: ‘Talkback Port’ and ‘Output Mute’. 

 

Audio  gain  values  are  now  set  in  dB  values  instead  of  percent  values.  (‘MicIn  Gain’,  ‘LineIn 
Gain’, ‘Output Gain’) 

 

Selectable network link mode. 

 

New system status parameter added: ‘Mac Address’ and ‘Link Mode’. 

 

Aspect ratio encoding option (4:3, 16:9, auto) is added. 

 

New video codec from ingenient is used. 

 
Version 0.9.22 

– 

06/16/2010  11:55 

 

Adjustable resolution (Full D1, Half D1 and SIF/CIF) is added.  

 

Improved talkback delay. 

 
 
 

Содержание ENC-200




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды