Teracue ENC-200 Скачать руководство пользователя страница 46

Страница: 46 / 59

ENC-200™ H.264 Encoder
User Guide V1.8

║ ║

║ ╠═══════► network/

║ ║

╠════►dhcp

DCHP (yes/no)

║ ║

╠════►ip_addr

ENC-200 IP-address

║ ║

╠════►subnet_mask

Subnet Mask

║ ║

╠════►broadcast_addr

Broadcast address; Read-only

║ ║

╠════►gateway_addr

Gateway address

║ ║

╠════►hostname

Hostname

║ ║

╠════►link_mode

Link Mode

║ ║

╚════►snmp/

║ ║

╠═════════► manager

Manager IP-address

║ ║

╠═════════► get_community

Get-Community password

║ ║

╠═════════► set_community

Set-Community password

║ ║

╠═════════► trap_community

Trap-Community password

║ ║

╠═════════► location

Location of the SNMP device

║ ║

╠═════════► contact

Contact person

║ ║

╚═════════► name

SNMP device name

║ ║

║ ╠═══════► comport/

║ ║

╠════►mode

Comport mode

║ ║

╠════►bitrate

Bitrate

║ ║

╠════►databits

Databits (7/8)

║ ║

╠════►parity

Parity (none/odd/even)

║ ║

╚════►stopbits

Stopbits (1/2)

║ ║

║ ╚═══════► system/

║

╠════►date

Date; MM/DD/YYYY

║

╚════►time

Time; HH:MM; 24hours

║

╚►status/

╠═══════► system/

║

╠════►board_version

ENC-200 Hardware Version

║

╠════►software_version

║

╠════►uptime

System uptime

║

╠════►arm

ARM load (%)

║

╠════►dsp

DSP load (%)

║

╠════►mac_address

MAC Address of the board

║

╠════►link_mode

Link Mode

║

╠════►date

Date

║

╚════►time

Time

║

╚═══════► encoder/

╚════►0/

╠═════════► encoder_running

Encoder runs status; Read-only

╠═════════► bytes_transmitted

Transmitted Bytes; Read-only

╠═════════► transportrate

Transport rate in kpbs; Read-only

╠═════════► input_locked

Video Input locked; Read-only

╚═════════► gpio/

╚════════► gpivalue

GPI Value; Read-only

Figure 32: Telnet directory structure for Remote Control testing

* = Is not supported at the moment

Содержание ENC-200




























































Результаты поиска

Содержание ENC-200

Отзывы:

Бренды по названию

Популярные бренды

Teracue ENC-200, Руководство пользователя

Результаты поиска

Содержание ENC-200

Отзывы:

Бренды по названию

Популярные бренды