manualshive.com logo in svg

Teracue ENC-200, Руководство пользователя

Поделиться
Скачать
Teracue ENC-200 Скачать руководство пользователя страница 55

ENC-200™ H.264 Encoder 
User Guide V1.8 
 

 

55

 

5.  Technical Specification 

 

ENC-200™: 

ENC-200™: 

H.264  SD  encoder  blade  with  analogue  video  input  and  SDI  input, 
embedded  audio  supported.  The  BNC  connector  on  the  front  panel  can 
be configured as Composite- or as SDI-input via jumper. 
 

 

The  ENC-200™  is  delivered  with  the  BREAK-OUT  cable  S  as  standard. 
Teracue  also  offers  a  professional  BREAK-OUT  cable  P  which  must  be 
ordered separately. 
 

 

S  – 

YC (MiniDIN), CVBS (RCA), Analogue Audio In (RCA), Analogue 
Audio Out (RCA) 

 

P  – 

YPbPr,  YC,  CVBS,  Genlock,  AES-3id  (BNC),  Audio  Out/In 
(RCA), GPI In/Out (Sub-D 9pin), RS-232 (Sub-D 9pin) 

 

 

Encoding Specifications: 

Standards: 

PAL, NTSC 

Video Inputs: 

Composite:  1  VPP,  75  Ohm;  Or  SDI  Output:  0,8  VPP,  75  Ohm 
(embedded audio support); This can be configured via jumper. 

Break-out cable inputs: 

Composite: 1 VPP, 75 Ohm 
S-Video: 1 VPP (Y), 0,3 VPP (C - Pal), 0,286 VPP (C - NTSC), 75 Ohm 
Component: 1 VPP (Y), 0,7 VPP (PBPR) , 75 Ohm 
Genlock: Blackburst 0,3 VPP, 75 Ohm 

Video Input Resolutions: 

Full D1: 720h x 480/576v, Half-D1: 352h x 480/576v, CIF/SIF: 360/384h x 
288/240v, QCIF: 176h x 144/120v 

Audio Inputs: 

Unbalanced Analog Stereo, Consumer Line level 
AES-3id, 75 Ohm, 1 VPP, Unbalanced 

Audio Outputs (Talkback):  Analog Stereo, Consumer Line level 
Video Codecs: 

MPEG-4  AVC/H.264  (ISO/IEC  14496-10),  Main  Profile  at  Level  3.1 
(MP@L3), Baseline Profile at Level 3.1 (BP@L3), 4:2.0 

Stream types: 

ISO/IEC 13818-1 Transport Streams 
Elementary A/V 

Audio Codecs: 

MPEG-4 AAC LC (ISO/IEC 14496-3) 
MPEG-1 Audio Layer II (ISO/IEC ISO/IEC 11172-3) 

 

 

I/O Specifications: 

Network: 

10/100TX Ethernet, RJ45, half/full duplex, Auto-sensing 

Streaming traffic: 

Unicast and Multicast traffic supported 

IP Protocols: 

HTTP  (Web  Browser),  TCP/IP  Control  Protocol,  UDP/IP  Streaming, 
TCP/IP Streaming, IGMPv2/3, SNMP, RTP*, RTCP*, RTSP*, DHCP 

RS-232 port: 

RS-232  connection  via  console  (Remote  control  for  non  IP  devices  via 
TCP/IP RS-232 command tunnelling*) 

GPI in*: 

1 INPUT, (for device control: Streaming on/off configuration*) 

GPI out: 

1 OUTPUT, for switching peripheral devices on/off 

 

 

Environmental: 

Agency Approvals: 

CE, RoHS compliant 

Humidity: 

Up to 90%, non-condensing 

Temperature: 

0  to  +60°C  environment temperature; fan  less  when  operated  in  FR-110 
or FR-210 frames 

Weight: 

Approx. 160 grams 

Blade dimensions (H/W/D):  20mm x 130mm x 190mm 
Power: 

5W per blade 

 

 

Limited Warranty: 

1 year standard limited warranty. Warranty extensions available 

 

 

 

 

 

 

Содержание ENC-200




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды