manualshive.com logo in svg

Teracue ENC-200, Руководство пользователя

Поделиться
Скачать
Teracue ENC-200 Скачать руководство пользователя страница 29

ENC-200™ H.264 Encoder 
User Guide V1.8 

 

29

 

3.4.4 

Menu: Network / SNMP (Simple Network Management 
Protocol) 

 
The Simple Network Management Protocol enables you to monitor and/or configure network attached 
devices like the ENC-200™, made possible by the installed SNMP agents.  
 
Every ENC-200™ since Firmware Version 0.9.23 is delivered with an SNMP agent. All you need are 
the  MIB  (Management  Information  Base)  files.  With  these  MIB  files  you  can  use  all  advantages  of 
SNMP associated with the ENC-200™. 
 
You  can  find  the  appropriate  MIB  files,  ‘TERACUE-ENC200-MIB.txt’  and  ‘TERACUE-SNMP-MIB.txt’ 
on the Teracue website IPTV Support Area. Or contact 

[email protected]

. 

 
With these MIBs and a SNMP manager, you have the possibility, to monitor the ENC-200™ status (by 
SNMP traps) or remotely configure every function of the ENC-200™ similar to the normal access via 
your  web  browser.  There  are  various  SNMP  management-tools  available  to  issue  SNMP  based 
commands to the appliance (Software not supplied by Teracue).  
 

.!. 

Set your SNMP manager to SNMPv2. 

 
Teracue uses the MIB Browser by iReasoning to monitor/set up the ENC-200™. iReasoning offers a 
free version of the MIB Browser under 

www.ireasoning.com

, which is useful to read the actual status 

or setting up the ENC-200™. See further information about the MIB Browser of iReasoning in chapter 
3.4.4.1 on page 31.  
 
SNMP  uses  the  following  standard  ports:  Port  161  and  port  162.  Port  161  is  used  by  the  SNMP 
manager  and  the  agent  to  send  the  requests  and  their  responses.  Port  162  is  used  by  the  SNMP 
agent  to  send  TRAPs  to  the  SNMP  manager.  Make  sure  that  these  ports  are  not  blocked  in  your 
network. 
 
The following operations are possible with SNMP: 

GET:

   

Read out the management information.  

GETNEXT:

 

Read out the management information iteratively, this is useful when you want to read 

 

 

the information down the MIB tree step by step. 

GETBULK:

 

Read out the management information of the complete list/tree. 

SET:

 

 

Change/set the management information. 

TRAP:

   

Start the Trap receiver in  your SNMP manager to get alerts  of the managed system. 

 

 

E.g. the encoder was started / stopped. 

 
To use the ENC-200™ SNMP features, you have to set up the encoder, to establish access with your 
SNMP manager. 
 

Содержание ENC-200




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды