Pulse Dial Option
Press:
#
*
12
*
<pulse-dial> #
0
= disable Pulse Dialing capability (default)
1
= enable Pulse Dialing capability
Auto Dial
The SX5 will recognize frequently called phone numbers and send them without waiting for the
Dial Delay. Up to 50 numbers that have been successfully called at least twice will be stored
when this feature is enabled. Any loss of power to the SX5 will clear this list.
Press:
#
*
21
*
<auto dial> #
0
= disable Auto Dial option (default)
1
= enable Auto Dial option
On-Hook Idle Voltage
This feature has been added to the SX5 and allows control of the on-hook idle voltage at the RJ-
11. It is recommended that only a qualified technician for PBX or payphone environments should
only change this parameter. Contact your installer for more information.
Press:
# * 134 * <mode> #
0
= Low battery mode and forward active when on-hook (default).
1
= High battery mode and low power standby when on-hook
SIM Settings
The SIM card used in the SX5 allows a PIN to be used to protect the unit from unauthorized use.
The PIN can be between 4 and 8 digits in length and any combination of digits 0 through 9. If
you are concerned about your SIM card being used in other devices without your knowledge,
you may use one of the Mobile Equipment Personalization (MEP) locks of the SX5. Ask your
service provider about for more information
SIM PIN 1 Setup
When enabled, a PIN must be entered every time the SX5 is powered on. The SX5 will not oper-
ate until the PIN is entered. To avoid having to enter the PIN each time the SX5 is
powered on (including after power interruptions or power outages), be sure to disable the SIM
PIN when the SIM card is installed.
• To
enable
SIM PIN 1, pick up the telephone handset and press:
#
*
104
*
1
*
<PIN 1> #
• To
disable
SIM PIN 1, pick up the telephone handset and press:
#
*
104
*
0
*
<PIN 1> #
HINT:
It is recommended that SIM PIN 1 be
disabled
so that it is not required to enter the PIN
each time the SX5 is powered on. Enable SIM PIN 1 only if it is certain that no one else should
use the SX5 to make calls. Be sure to inform your service provider if you do
not
want SIM PIN 1
enabled when you get your SIM card.
Auto SIM PIN Entry (PIN 1 Only)
When SIM PIN 1 is enabled and the SX5 is powered on, entry of the PIN will be required. To by-
pass the requirement to always enter the PIN every time power is cycled (power outages, reloca-
tion of the unit, etc.), enable Auto SIM PIN Entry. If SIM PIN 1 is not enabled, enabling this fea-
ture has no effect.
Enable
Auto SIM Pin Entry is the factory default.
• To
enable
Auto SIM PIN Entry, pick up the telephone handset and press:
#
*
65
*
1
*
<PIN 1> #
• To
disable
Auto SIM PIN Entry, pick up the telephone handset and press:
#
*
65
*
0
*
<PIN 1> #
NOTE:
If you enable this feature and change the SIM card in the unit, you will have to enter the
SIM PIN of the new card before the SX5 will be operational.
Caller ID
The SX5 will support Caller ID device operation. The default format setting is designed to work
for most Caller ID devices.
Change Caller ID Format
The following key sequence is used to select the Caller ID (CID) format:
Press:
#
*
84
*
<CID format> # <Flash>
1
= MDMF (Multiple Data Message Format) (default)
2
= SDMF (Single Data Message Format)
3
= OFF
Phonecell
®
SX5 GSM
9
User Manual
