Telit Wireless Solutions UC864-E, Справочное руководство

Страница: 70 / 329

UC864 UC864 UC864 UC864----E/G/WD/WDU E/G/WD/WDU E/G/WD/WDU E/G/WD/WDU AT Commands Reference Guide AT Commands Reference Guide AT Commands Reference Guide AT Commands Reference Guide
80304ST10041a Rev. 6 80304ST10041a Rev. 6 80304ST10041a Rev. 6 80304ST10041a Rev. 6 ---- 2010 2010 2010 2010----0 00 05 55 5----20 20 20 20
Reproduction forbidden without Telit Communications S.p.A’s. written authorization - All Rights Reserved. Page 70 of 329
3.5.3.7.2. Ring Counter Ring Counter Ring Counter Ring Counter ---- S1 S1 S1 S1
S1
S1 S1
S1 ---- Ring Counter
Ring Counter Ring Counter
Ring Counter
ATS1 ATS1 ATS1 ATS1 S1 S1 S1 S1 is incremented each time the device detects the ring signal of an
incoming call. S1
S1 S1
S1 is cleared as soon as no ring occur.
Note: the form ATS1
ATS1 ATS1 ATS1 has no effect.
ATS1?
ATS1? ATS1?
ATS1? Read command returns the value of this parameter.
3.5.3.7.3. Escape Character Escape Character Escape Character Escape Character ---- S2 S2 S2 S2
S2 S2 S2 S2 ---- Escape Character Escape Character Escape Character Escape Character
ATS2=[<char>] ATS2=[<char>] ATS2=[<char>] ATS2=[<char>] Set command sets the ASCII character to be used as escape character.
Parameter:
<char>
<char> <char>
<char> - escape character decimal ASCII
0..255 - factory default value is 43 (+).
Note: the escape sequence consists of three escape characters preceded
and followed by
n nn n
ms of idle (see S12 S12 S12 S12 to set
n nn n
).
ATS2? ATS2? ATS2? ATS2? Read command returns the current value of S S S S2 22 2 parameter.
Note: the format of the numbers in output is always 3 digits, left-filled with
0s
3.5.3.7.4. Command Line Termination Character Command Line Termination Character Command Line Termination Character Command Line Termination Character ---- S3 S3 S3 S3
S3 S3 S3 S3 ---- Command Line Termination Character Command Line Termination Character Command Line Termination Character Command Line Termination Character
ATS3=[<char>] ATS3=[<char>] ATS3=[<char>] ATS3=[<char>] Set command sets the value of the character either recognized by the
device as command line terminator and generated by the device as part of
the header, trailer, and terminator for result codes and information text,
along with S4
S4 S4
S4 parameter
parameter parameter
parameter.
Parameter:
<char>
<char> <char> <char> - command line termination character (decimal ASCII)
0..127 - factory default value is 13 (ASCII <CR>
<CR> <CR>
<CR>)
Note: the “previous” value of S3
S3 S3
S3 is used to determine the command line
termination character for entering the command line containing the S3 S3 S3 S3
setting command. However the result code issued shall use the “new” value
of S3
S3 S3 S3 (as set during the processing of the command line)
ATS3? ATS3? ATS3? ATS3? Read command returns the current value of S3 parameter S3 parameter S3 parameter S3 parameter.
Note: the format of the numbers in output is always 3 digits, left-filled with