Telit Wireless Solutions HE910-EU V2 Скачать руководство пользователя страница 56

Страница: 56 / 78

The HE910 V2 module provides a Digital to Analog Converter. The signal (named
DAC_OUT) is available on pin C13 of the HE910 V2 module and on pin 6 of PL302 on
Interface Board (CS1467D).

The on board DAC is in the range from 0 to 1023. However, an external low-pass filter is
necessary.

Parameter

Min

Max

Units

Voltage range (filtered)

1.8

Volt

Range

1023

Steps

The precision is 1023 steps, so since the maximum voltage is 2V, the integrated voltage could
be calculated with the following formula:

Integrated output voltage = 2 * value / 1023

DAC_OUT line must be integrated (for example with a low band pass filter) in order to obtain
an analog voltage.

An AT command is available to use the DAC function.

The command is: AT#DAC[=<enable>[,<value>]]

<value> - scale factor of the integrated output voltage (0..1023 ~ 10 bit precision)

it must be present if <enable>=1

Refer to SW User Guide or AT Commands Reference Guide for the full description of this
function.

NOTE:

The DAC frequency is selected internally. D/A converter must not be used during
POWERSAVING.

Содержание HE910-EU V2















































































Результаты поиска

Содержание HE910-EU V2

Отзывы:

Бренды по названию

Популярные бренды

Telit Wireless Solutions HE910-EU V2, Руководство пользователя по оборудованию

Результаты поиска

Содержание HE910-EU V2

Отзывы:

Бренды по названию

Популярные бренды