manualshive.com logo in svg

Telit Wireless Solutions HE910-EU V2, Руководство пользователя по оборудованию

Поделиться
Скачать
Telit Wireless Solutions HE910-EU V2 Скачать руководство пользователя страница 24

 
 

 

 

 

 

During the 

Initialization state

, any kind of AT-command is not available.  DTE must wait for 

the 

Activation state

 to communicate with HE910 V2. 

To check if the HE910 V2 has powered on, the hardware line PWRMON must be monitored. 
When PWRMON goes high, the module has powered on. 

 

NOTE: 

Do not use any pull up resistor on the ON_OFF* line. It is pulled up internally. Using a pull 
up  resistor  may  bring  latch  up  problems  on  the  HE910  V2  power  regulator  and  improper 
power  on/off  of  the  module.  The  line  ON_OFF*  must  be  connected  only  in  open  collector 
configuration. 

 

NOTE: 

In  this  document  all  the  lines  are  inverted.  Active  low  signals  are  labeled  with  a  name  that 
ends with "*" or with a bar over the name. 

 

NOTE: 

In order to avoid a back powering effect it is recommended to avoid having any HIGH logic 
level signal applied to the digital pins of the HE910 V2 module when the module is powered 
OFF or during an ON/OFF transition. 

 

For example: 

1.

 

To  drive  the  ON_OFF*  pad  with  a  totem  pole  output  of  a  +3/5  V  microcontroller 
(uP_OUT1): 

 

Содержание HE910-EU V2















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды