manualshive.com logo in svg

Telit Wireless Solutions HE910-EU V2, Руководство пользователя по оборудованию

Поделиться
Скачать
Telit Wireless Solutions HE910-EU V2 Скачать руководство пользователя страница 44

 
 

 

 

 

 

 

The HE910 V2 module includes a Universal Serial Bus (USB) transceiver, which operates at 
USB high-speed (480Mbits/sec).  

It  is  compliant  with  the  USB  2.0  specification  and  can  be  used  for  diagnostic  monitoring, 
control and data transfers. 

The table below describes the USB interface signals: 

 

Pin 

Signal 

I/O 

Function 

Type 

B15

 

USB_D+ 

I/O 

USB differential Data(+) 

 

C15

 

USB_D- 

I/O 

USB differential Data(+) 

 

A13 

VBUS 

I 

Power sense for the internal USB transceiver 

5V 

 
 

The  USB_DPLUS  and  USB_DMINUS  signals  have  a  clock  rate  of  480MHz.  The  signal 
traces should be routed carefully. Trace lengths, number of vias and capacitive loading should 
be minimized. The impedance value should be as close as possible to 90 Ohms differential.

 

 

WARNING: 

Consider a mechanical design and a low-capacitance ESD protection device to protect HE910 
V2 or customer specific requirements from ESD event to USB lines (B15, C15 and A13). 

 
 
 
 
 
 
 
 
 

Содержание HE910-EU V2















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды