manualshive.com logo in svg

Telit Wireless Solutions HE910-EU V2, Руководство пользователя по оборудованию

Поделиться
Скачать
Telit Wireless Solutions HE910-EU V2 Скачать руководство пользователя страница 43

 
 

 

 

 

 

This line of transmission shall fulfill the following requirements: 

Antenna Line on PCB Requirements 

Characteristic Impedance 

50Ohm 

Max Attenuation 

0.3dB 

Coupling with other signals shall be avoided 

Cold End (Ground Plane) of antenna shall be equipotential to the HE910 V2  ground pads 

 

Furthermore if the device is developed for the US and/or Canada market, it must comply with 
the FCC and/or IC requirements. 

This device is to be used only for mobile and fixed application.   

 

 

Ensure that the antenna line impedance is 50ohm. 

 

Keep line on the PCB as short as possible to reduce the loss. 

 

Antenna line must have uniform characteristics, constant cross section, avoid meanders 
and abrupt curves. 

 

Keep one layer of the PCB used only for the Ground plane; if possible. 

 

Surround (on the sides, over and under) the antenna line on PCB with Ground.   Avoid 
having other signal tracks directly facing the antenna line track. 

 

The  Ground  around  the  antenna line  on  PCB  has  to  be  strictly  connected  to  the  main 
Ground plane by placing vias once per 2mm at least. 

 

Place EM noisy devices as far as possible from HE910 V2 antenna line. 

 

Keep the antenna line far away from the HE910 V2 power supply lines.  

 

If EM noisy devices are around the PCB hosting the HE910 V2, such as fast switching 
ICs,  take  care  of  shielding  of  antenna line  by  burying  it  inside  the layers of  PCB  and 
surround it with Ground planes; or shield it with a metal frame cover.

 

 

If you do not have EM noisy devices around the PCB of HE910 V2, use a strip line on 
the superficial copper layer for the antenna line. The line attenuation will be lower than 
a buried one.

 

 

 

The  HE910  V2,  due  to  its  sensitivity  characteristics,  is  capable  of  performing  a  fix 
inside  buildings.  (In  any  case  the  sensitivity  could  be  affected  by  the  building 
characteristics i.e. shielding) 

 

The Antenna must not be co-located or operating in conjunction with any other antenna 
or transmitter. 

 

Antenna shall not be installed inside metal cases. 

 

Antenna shall be installed also according antenna manufacture instructions. 

 

Содержание HE910-EU V2















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды