manualshive.com logo in svg

Telit Wireless Solutions HE910-EU V2, Руководство пользователя по оборудованию

Поделиться
Скачать
Telit Wireless Solutions HE910-EU V2 Скачать руководство пользователя страница 45

 
 

 

 

 

 

 

The  serial  ports  on  the  Telit  HE910  V2  are  the  interface  between  the  module  and  OEM 
hardware.  

2 serial ports are available on the module: 

 

Modem Serial Port 1 (Main) 

 

Modem Serial Port 2 (Auxiliary) 

Several configurations can be designed for the serial port on the OEM hardware.  

The most common are: 

 

RS232 PC comport 

 

Microcontroller [email protected](Universal Asynchronous Receiver Transmit) 

 

Microcontroller UART@5V or other voltages different from 1.8V 

Depending on the type of serial port on the OEM hardware, a level translator circuit may be 
needed to make the system work.  

Serial port 1 is a +1.8V UART with all the 7 RS232 signals.  

Serial port 2 is a +1.8V Auxiliary

 

UART. 

 

The electrical characteristics of the serial port are explained in the following tables: 

Absolute Maximum Ratings -Not Functional 

Parameter 

Min 

Max 

Input level on non-power pin with respect to ground 

-0.3 

+2.3V 

 

Operating Range - Interface levels 

Parameter 

Min 

Max 

Input high level 

1.5V 

2.1 V 

Input low level 

-0.3V 

0.35V 

Output high level 

1.35V 

1.8V 

Output low level 

0V 

0.45V 

Содержание HE910-EU V2















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды