manualshive.com logo in svg

Telit Wireless Solutions HE910-EU V2, Руководство пользователя по оборудованию

Поделиться
Скачать
Telit Wireless Solutions HE910-EU V2 Скачать руководство пользователя страница 31

 
 

 

 

 

 

Mode 

Average(mA) 

Mode Description 

GSM TX and RX mode 

Operating mode 

GPRS 4TX/2RX 

600 

GSM850/GSM900, class33 

450 

DCS1800/PCS1900, class33 

EDGE 4TX/2RX 

400 

GSM850/GSM900, class33 

350 

DCS1800/PCS1900, class33 

GSM peak current 

1800 

 

 
(*1) The off current is the total supply current from the main battery with the PMIC off and 
the 32 kHz XTAL oscillator on. 
(*2) Worst/best case depends on network configuration and is not under module control. 
(*3) GPRS with PDP context active 

 

NOTE: 

The  Operating  Voltage  Range  MUST  never  be  exceeded.  Special  care  must  be  taken  when 
designing the application’s power supply section to avoid having an excessive voltage drop. 

If the voltage drop is exceeding the limits it could cause a Power Off of the module. 

Behavior in the extended operating voltage range might deviate from 3GPP3 specification. 

 

NOTE: 

The electrical design for the Power supply must be made ensuring that it will be capable of a 
peak current output of at least 2A. 

 

In GSM/GPRS mode, RF transmission is not continuous and it is packed into bursts at a base 
frequency of about 216 Hz, and the relative current peaks can be as high as about 2A. 
Therefore the power supply has to be designed in order to withstand these current peaks 
without big voltage drops; this means that both the electrical design and the board layout must 
be designed for this current flow. If the layout of the PCB is not well designed, a strong noise 
floor is generated on the ground; this will reflect on all the audio paths producing an audible 
annoying noise at 216 Hz; if the voltage drops during the peak, current absorption is too much. 
The device may even shut down as a consequence of the supply voltage drop. 

Содержание HE910-EU V2















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды