Telestream PRISM MPI-UP PHY-12G Скачать руководство пользователя страница 35

Страница: 35 / 40

PRISM Field Upgrade Kit Instructions

While the upgrade is in process, a message box appears stating that

the firmware installation is in progress. (See

Figure 77

CAUTION.

Removing the USB device or powering off the instrument before the

upgrade is complete can cause upgrade failure. To prevent upgrade failure, wait until

the Installation Complete

message box is displayed before performing these actions.

The upgrade may take up to five minutes.

NOTE.

The upgrade may take up to five minutes.

Figure 30: Upgrade Installation In-Process message box

Remove the USB device from the PRISM monitor.

Verify the firmware

upgrade

Select the

Settings

icon (

) to open the Settings menu.

Select

Utilities

to open the Utilities submenu.

Select

Version

to open the Version display.

Verify the displayed firmware version number matches the version of

the firmware upgrade package you installed.

Содержание PRISM MPI-UP PHY-12G









































Результаты поиска

Содержание PRISM MPI-UP PHY-12G

Отзывы:

Похожие инструкции для PRISM MPI-UP PHY-12G

Бренды по названию

Популярные бренды

Telestream PRISM MPI-UP PHY-12G, Инструкции по модернизации оборудования

Результаты поиска

Содержание PRISM MPI-UP PHY-12G

Отзывы:

Похожие инструкции для PRISM MPI-UP PHY-12G

Бренды по названию

Популярные бренды