Teledyne Genie Nano Series Скачать руководство пользователя страница 96

Страница: 96 / 121

•

Technical Specifications

Nano Series GigE Vision Camera

Opto-coupled Output:

AC Characteristics at an internal FPGA temperature of 83C

Output

Common

Power

Output

Current

load

Test

d1 (

µs)

Leading Delay

rise (

µs)

Rise Time

d2 (

µs)

Trailing Delay

fall (

µs)

Fall Time

8 mA

250 ohm

0.41

2.5

8.5

20.6

16 mA

75 ohm

0.42

4.6

1.9

12.9

8 mA

500 ohm

4.6

2.5

10.1

21.6

16 mA

200 ohm

0.45

4.5

2.9

12.9

21 mA

45 ohm

0.38

3.5

1.5

7.9

12V

8 mA

1.4K ohm

0.49

1.7

15.3

24.1

16 mA

625 ohm

0.59

3.1

4.3

14.9

24 mA

260 ohm

0.51

2.6

2.5

8.4

24V

8 mA

2.87K ohm

0.65

1.8

20.8

31.0

16 mA

1.38K ohm

0.64

2.1

6.9

19.1

24 mA

617 ohm

0.68

2.6

12.0

Computer Requirements for Nano Cameras

The following information is a guide to computer and networking equipment required to support the

Nano camera at maximum performance. The Nano camera series complies with the current IPv4

Internet Protocol, therefore current Gigabit Ethernet (GigE) equipment should provide trouble free

performance.

Host PC System

•

Operating System: Windows 7, 8.0, 8.1 (either 32-bit or 64-bit for all) are supported.

•

Operating System: Linux (scheduled support - TBD)

Network Adapters

•

GigE network adapter (either add on card or on motherboard). The Intel PRO/1000 MT

adapter is an example of a high performance NIC. Typically a system will need an Ethernet

GigE adapter to supplement the single NIC on the motherboard.

•

PCI Express adapters will outperform PCI adapters.

•

Network adapters that support Jumbo Frames will outperform adapters with fixed packet

size frames.

•

10/100 Ethernet is not supported.

Laptop Information

•

Older laptop computers with built in GigE network adapters may still not be able to stream

full frame rates from Nano. Thorough testing is required with any laptop computer to

determine the maximum frame rate possible (refer to the Teledyne DALSA Network Imaging

Package user's manual).

Ethernet Switch Requirements

When there is more than one device on the same network or a camera-to-PC separation greater

than 100 meters, an Ethernet switch is required. Since the Genie Nano GigE camera complies with

Содержание Genie Nano Series


























































































































Результаты поиска

Содержание Genie Nano Series

Отзывы:

Похожие инструкции для Genie Nano Series

Бренды по названию

Популярные бренды

Teledyne Genie Nano Series, Руководство пользователя

Результаты поиска

Содержание Genie Nano Series

Отзывы:

Похожие инструкции для Genie Nano Series

Бренды по названию

Популярные бренды