Teledyne Genie Nano Series Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 121

Teledyne Genie Nano Series Скачать руководство пользователя страница 71

Nano Series GigE Vision Camera

Operational Reference

•

69

Internal Test Pattern Generator

The Genie Nano camera includes a number of internal test patterns which easily confirm camera

installations, without the need for a camera lens or proper lighting.
Use CamExpert to easily enable and select the any of the Nano test patterns from the drop menu

while the camera is not in acquisition mode. Select live grab to see the pattern output.
Note that internal test patterns are generated by the camera FPGA, thus are identical for

monochrome or color camera models.

The Nano Test Patterns are:

•

Grey Horizontal ramp: Image is filled horizontally with an image that goes from the darkest

possible value to the brightest.

•

Grey Vertical ramp: Image is filled vertically with an image that goes from the darkest

possible value to the brightest.

•

Grey Diagonal Ramp Moving: combination of the 2 previous schemes, but first pixel in image

is incremented by 1 between successive frames. This is a good pattern to indicate motion when

doing a continuous grab.

«
...
69
70
71
72
73
...
»

Содержание Genie Nano Series


























































































































Отзывы:

Нет отзывов