Teledyne Genie Nano Series Скачать руководство пользователя страница 113

Страница: 113 / 121

Nano Series GigE Vision Camera

Troubleshooting

•

111

•

There is no image but the frame rate is as expected.

See Camera is functional, frame rate is as expected, but image is black.

Other problems

•

Unexpected or missing 'Trigger Events'. See Random Invalid Trigger Events.

Verifying Network Parameters

Teledyne DALSA provides the Network Configuration tool to verify and configure network devices

and the Nano network parameters. See section Network Configuration Tool of the Teledyne DALSA

Network Imaging manual, if there were any problems with the automatic Nano software

installation.

Before Contacting Technical Support

Carefully review the issues described in this Troubleshooting section. To aid Teledyne DALSA

personnel when support is required, the following should be included with the request for support.

•

From the Start menu, go to Programs • Dalsa • Sapera LT • Tools and run the Log Viewer

program. From its File menu click on Save Messages to generate a log text file.

•

Report the version of Genie Nano Framework and Sapera version used.

Device Available with Operational Issues

This section considers issues with cabling, Ethernet switches, multiple cameras, and camera

exposure. All information concerning the Teledyne DALSA Network Configuration Tool and other

networking considerations, is available in the Teledyne DALSA Network Imaging manual.

Firmware Updates

As a general rule any Nano installation must include the firmware update procedure

(see File Access Control Category). Nano camera firmware that does not match a newer version of

installed Nano Framework software is likely to have unpredictable behavior.
Problems might be:

•

Nano is not found by the device discovery process.

•

Nano is found by the Sapera GigE Server but an application such as CamExpert does not see

the camera.

•

A Nano that had a fault with a firmware update will automatically recover by booting with the

previous firmware version.

Important: New Nano cameras installed in previously deployed systems are fully backward

compatible with the older vision application.

Содержание Genie Nano Series


























































































































Результаты поиска

Содержание Genie Nano Series

Отзывы:

Похожие инструкции для Genie Nano Series

Бренды по названию

Популярные бренды

Teledyne Genie Nano Series, Руководство пользователя

Результаты поиска

Содержание Genie Nano Series

Отзывы:

Похожие инструкции для Genie Nano Series

Бренды по названию

Популярные бренды