Teledyne Genie Nano Series Скачать руководство пользователя страница 43

Страница: 43 / 121

Nano Series GigE Vision Camera

Operational Reference

•

Internal Programmable Exposure (ExposureMode = Timed)

The Genie Nano in Internal Programmable Timed Exposure mode has the following features:

•

Programmable internal trigger, where the maximum and minimum sensor frame rate limits are

defined by the ExposureTime feature.

•

Exposure synchronization timing is Synchronous Mode where the exposure is aligned with the

sensor horizontal line timing and the next acquisition is triggered by an internal programmable

timer.

•

Exposure duration is user programmable

•

Exposure maximum is dependent on the frame rate.

•

Minimum exposure (in µs) is model dependent.

•

Image readout is simultaneous where the grabbed image frame is readout during the next

frame exposure time. This allows for fastest possible frame rates.

FrameActive

Frame Inactive

Exposure

ReadOut

Exposure

Delay

Exposure Example

Free-running Exposure Timing

External Trigger: Programmable Exposure

•

Also known as “Edge Pre-select” exposure. See timing diagram below.

•

An external trigger edge initiates the exposure process.

•

The user programmable delay (exposureDelay) from valid trigger edge to start of exposure is

camera model specific.

•

Supports Synchronous Mode timing for fastest possible frame rates. Start of exposure is aligned

on the next horizontal line while the exposure duration period is in 1µs steps. Exposure and

sensor readout can be concurrent.

•

Exposure duration is programmable from the model dependent minimum to 16 seconds (in 1μs

steps).

•

Any external trigger received before the last exposure is ignored.

FrameActive (1)

Frame Inactive

FrameTrigger Inactive

Frame Inactive

FrameActive (2)

FrameTrigger Active

Exposure(1)

ReadOut

(1)

Exposure

Delay

Exposure(2)

ReadOut

(2)

Exposure

Delay

FrameTrigger Inactive

exposureAlignment=Synchronous

Invalid Frame Trigger Period

ValidFrameTrigger

Event (1)

ValidFrameTrigger

Event (2)

Invalid Frame Trigger Period

External Trigger Programmable Synchronous Mode Exposure Timing

Содержание Genie Nano Series


























































































































Результаты поиска

Содержание Genie Nano Series

Отзывы:

Похожие инструкции для Genie Nano Series

Бренды по названию

Популярные бренды

Teledyne Genie Nano Series, Руководство пользователя

Результаты поиска

Содержание Genie Nano Series

Отзывы:

Похожие инструкции для Genie Nano Series

Бренды по названию

Популярные бренды