Teledyne Genie Nano Series Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 121

background image

70

•

Operational Reference

Nano Series GigE Vision Camera

Acquisition and Transfer Control Category

The Genie Nano Acquisition and Transfer controls, as shown by CamExpert, groups parameters

used to configure the optional acquisition modes of the device.
Parameters in gray are read only, either always or due to another parameter being disabled.

Parameters in black are user set in CamExpert or programmable via an imaging application.
Features listed in the description table but tagged as Invisible are usually for Teledyne DALSA or

third party software usage—not typically needed by end user applications. Also important, Genie

Nano cameras are available in a number of models implementing different sensors and image

resolutions which may not support the full feature set defined in this category.

Acquisition and Transfer Control Feature Descriptions

The following table describes these parameters along with their view attribute and minimum

camera firmware version required. Additionally the Device Version column will indicate which

parameter is a member of the DALSA Features Naming Convention (denoted by DFNC), versus the

GenICam Standard Features Naming Convention (SFNC tag is not shown).
The Device Version number represents the camera software functional group, not a firmware

revision number. As Genie Nano capabilities evolve the device version tag will increase, therefore

identifying the supported function package. New features for a major device version release will be

indicated by

green text

for easy identification.

Display Name

Feature & Values

Description

Device Version

& View

Acquisition Status

Selector

AcquisitionStatusSelector

Selects the internal acquisition signal to read using

AcquisitionStatus.

1.00

Expert

Acquisition Active

AcquisitionActive Device is currently doing an acquisition of one or

many frames.

Acquisition Status

AcquisitionStatus

Reads the state of the internal acquisition signal

selected using the Acquisition Status Selector feature.

1.00

Expert

Acquisition Mode

AcquisitionMode

Set the acquisition mode of the device. It defines the

number of frames to capture during an acquisition

and the way the acquisition stops.

1.00

Beginner

«
...
70
71
72
73
74
...
»

Содержание Genie Nano Series


























































































































Отзывы:

Нет отзывов

Похожие инструкции для Genie Nano Series

Бренд: DAGE-MTI Страницы: 16

Бренд: NA-DE Страницы: 7

Бренд: MagicRadar Страницы: 98

Gemini GEM-X255

Бренд: NAPCO Страницы: 40

Бренд: NAPCO Страницы: 16

Бренд: NAPCO Страницы: 6

Бренд: Eaton Страницы: 23

Бренд: Digital Concepts Страницы: 2

Бренд: Tamron Страницы: 8

Enforcer EV-122C-FVA3Q

Бренд: SECO-LARM Страницы: 2

Бренд: TKH security Страницы: 29

Бренд: Dante Страницы: 40

Бренд: Ziton Страницы: 13

Бренд: Abus Страницы: 2

Бренд: Zhejiang Uniview Technologies Страницы: 28

Бренд: Absolute Process Instruments Страницы: 2

Бренд: Inter-m Страницы: 12

Бренд: Advent Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды