manualshive.com logo in svg

Teledyne Genie Nano Series, Руководство пользователя, Страница: 16 / 121

Поделиться
Скачать
Teledyne Genie Nano Series Скачать руководство пользователя страница 16

14  

•

  Genie Nano Series Overview 

Nano Series GigE Vision Camera 

† Dynamic Range Test Conditions 

•

 

Exposure 100µs 

•

 

0% Full Light Level 

†† SNR Test Conditions 

•

 

Exposure 2000µs 

•

 

80% saturation 

‡ Specifications calculated according to EMVA-1288 standard, using white LED light 

Sensor Cosmetic Specifications 

 

Blemish Specifications 

Maximum Number of 

Defects 

Blemish Description  

Hot/Dead Pixel defects ††† 

Typical 0.0025% 

Max 0.005% 

Any pixel that deviates by ±20% from the average of 

neighboring pixels at 50% saturation including pixel stuck at 0 

and maximum saturated value.  

Spot defects 

none 

Grouping of more than 8 pixel defects within a sub-area of 3x3 

pixels, to a maximum spot size of 7x7 pixels. 

Clusters defects 

none 

Grouping of more than 5 single pixel defects in a 3x3 kernel. 

Column defects 

none 

Vertical grouping of more than 10 contiguous pixel defects along 

a single column.  

Row defects 

none 

Horizontal grouping of more than 10 contiguous pixel defects 

along a single row.  

 

††† Test conditions 

•

 

Nominal light = illumination at 50% of saturation 

•

 

Temperature of camera is 45°C  

 

Содержание Genie Nano Series


























































































































Отзывы:

Нет отзывов