Teledyne Lecroy WavePro HD series Скачать руководство пользователя страница 7

Страница: 7 / 48

WavePro HD Getting Started Guide

OVERVIEW

The

touch screen display

is the principal viewing and control center of

the oscilloscope. See p.10 for an overview of its components.
The

front panel

houses buttons and knobs that control different

oscilloscope settings. Operate the instrument using front panel controls,

touch screen controls, or a mix that is convenient for you.
Front mounted

host USB 3.1 ports

can be used for transferring data or

connecting peripherals such as a mouse or keyboard.
The

mixed signal interface

connects the digital leadset to input up-to-16

digital lines (on -MS models).

Calibration output terminal

is used to compensate passive probes. The

Ground terminal

may be connected to a grounding wrist strap or the

ground lead on probes.

Channels

1–4 are used to input analog signal. The connectors are

equipped with the new ProBus2 interface, compatible with either legacy

ProBus or new ProBus2 probes. They can also accept a conventional

BNC cable.

Note:

The BNC inputs are rated to 8 GHz but will require a precision

adapter (available from Teledyne LeCroy Service) to accept SMA cables.
The

tilting feet

change the angle of display for easier viewing.

Powering On/Off

Connect the line cord rated for your country to the

AC power inlet

on the

back of the instrument, then plug it into a grounded AC power outlet. (See

Power in “Safety”).
The

Power button

controls the operational state of the oscilloscope.

Press Power to switch on the instrument and load the oscilloscope software.

The LED on the button lights to show the oscilloscope is on. Press it again to

switch “off” (Standby power).

CAUTION.

Do not power on or calibrate the oscilloscope with a

signal attached.

Always use the Power button or the

File > Shutdown

menu option to

execute a proper shut down process and preserve settings.
The Power button does not disconnect the oscilloscope from the AC

power supply; some “housekeeping” circuitry continues to draw power.

The only way to fully power down the instrument is unplug the AC line

cord from the outlet.

CAUTION

. Do not place the instrument so that it is difficult to reach

the power cord in case you need to disconnect from power.

We recommend unplugging the instrument if it will remain unused for a

long period of time.

Содержание WavePro HD series
















































Результаты поиска

Содержание WavePro HD series

Отзывы:

Teledyne Lecroy WavePro HD series, Руководство по началу работы, Страница: 7 / 48

Результаты поиска

Содержание WavePro HD series

Отзывы: