Teledyne Lecroy WavePro HD series Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 48

Teledyne Lecroy WavePro HD series Скачать руководство пользователя страница 34

929412-00 Rev A

32

When you use the front panel Zoom button, a new Zoom trace is created for

every open trace, showing a 10x magnification of the source trace.
The zoomed portion of the original trace is highlighted, so that the area

corresponding to the zoom is more visible.

BASICS

Create

Zoom

of

all open traces.

The

Zoom descriptor box

shows the

Zoom Source

and

Horizontal Scale

, which

differs from the Timebase.

Adjust

Horizontal Scale

to change zoom

magnification.

Zoom

Zoom traces display a magnified portion of another trace. Any trace can be zoomed, although Zoom is most useful for channel traces, as it allows you to see the

source at the original Timebase at the same time as the Zoom "close up." Zoom is also useful for analyzing regions of >500 Mpts acquisitions that fall outside the

center Analysis Zone. Use the Zoom trace as the source for measurements or math functions.

From the Front Panel

«
...
32
33
34
35
36
...
»

Содержание WavePro HD series

















































Отзывы:

Нет отзывов