Teledyne Lecroy Frontline BPA 600 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 348

Teledyne Lecroy Frontline BPA 600 Скачать руководство пользователя страница 67

3.4.2

Bluetooth

low energy Transmitter

A

Bluetooth

low energy device maximum operating range is directly related to the power output. The power

output is important in conductive testing because the DUTs and the Frontline unit are connected directly to
each other, usually over small distances. The absence of power loss, which occurs during over-the-air
transmission, means that larger than normal power levels may be present at the receiving port. Attenuation
may be necessary to protect both the DUT and the Frontline unit from excessive power input and to ensure
reliable operation.

Bluetooth low energy Transmitter below

lists the maximum power and operating range for

Bluetooth

low

energy transmitters.

Bluetooth SIG

Specification

Maximum

Power

Operating

Range

Up to 4

10 dBm (5 mW)

50 meters

Table 3.12 -

Bluetooth

low energy Transmitter

Caution:

Good engineering judgment is essential to protecting both the Frontline low

energy protocol analyzer and the devices under test from power levels that could
cause damage. The procedures contained here are general guidelines for connecting
the equipment for conductive testing.

3.4.3 BPA 600 Conductive Testing

Test Equipment

While exact conductive test setups are dependent on the specific circumstances surrounding the DUT RF
interface, the following equipment is required for all test setups.

l

Coaxial cable with adapter for connecting to DUT 1.

l

Coaxial cable with adapter for connecting to DUT 2.

l

2 Coaxial T-connectors.

l

2 SMA adapters for connecting coaxial cable or attenuators to the BPA 600 antenna connectors.

l

Attenuators depending on the

Bluetooth

Class being tested.

l

Frontline BPA 600 Dual Mode

Bluetooth

Protocol Analyzer

l

Personal computer for running Frontline software.

Test Set Up

BPA 600 Conductive Test Setup on page 60

shows the test setup.

TELEDYNE LECROY

Chapter 3 Configuration Settings

59

Frontline BPA 600 Hardware & Software User Manual

«
...
65
66
67
68
69
...
»

Содержание Frontline BPA 600





























































































































































































































































































































































Отзывы:

Нет отзывов