Tektronix 442, Инструкция по эксплуатации

Страница: 166 / 170

CALIBRATION TEST EQUIPMENT REPLACEMENT
Calibration Test Equipment Chart
This chart compares TM 500 product performance to that of older Tektronix equipment. Only those
characteristics where significant specification differences occur, are listed. In some cases the new instrument
may not be a total functional replacement. Additional support instrumentation may be needed or a change in
calibration procedure may be necessary.
Comparison of Main Characteristics
DM 501 replaces 7D13
PG 501 replaces 107
PG 501 - Risetime less than 107 - Risetime less than
3.5 ns into 50 O. 3.0 ns into 50 fi.
108 PG 501 - 5 V output pulse; 108 - 10 V output pulse
3.5 ns Risetime 1 ns Risetime
PG 502 replaces 107
108 PG 502 - 5 V output 108 - 10 V output
111 PG 502 - Risetime less than
111 - Risetime 0.5 ns; 30
1 ns; 10 ns to 250 ns
Pretrigger pulse
Pretrigger pulse
delay
delay
PG 508 replaces 114
Performance of replacement equipment is the same or
115
better than equipment being replaced.
2101
PG 506 replaces 106 PG 506 - Positive-going
106 - Positive and Negative-
trigger output sig-
going trigger output
nal at least 1 V; signal, 50 ns and 1 V;
High Amplitude out- High Amplitude output,
put, 60 V.
100 V.
067-0502-01 PG 506 - Does not have 0502-01 - Comparator output
chopped feature.
can be alternately
chopped to a refer-
ence voltage.
SG 503 replaces 190,
190A, 190B SG 503 - Amplitude range 190B - Amplitude range 40 mV
5 mV to 5.5 V p-p. to 10 V p-p.
191
067-0532-01 SG 503 - Frequency range 0532-01 - Frequency range
250 kHz to 250 MHz. 65 MHz to 500 MHz.
SG 504 replaces
067-0532-01
SG 504 - Frequency range 0532-01 - Frequency range
245 MHz to 1050 MHz. 65 MHz to 500 MHz.
067-0650-00
TG 501 replaces 180,
180A TG 501 - Trigger output- 180A - Trigger pulses 1, 10,
slaved to marker 100 Hz; 1, 10, and
output from 5 sec 100 kHz. Multiple
through 100 ns. One time-marks can be
time-mark can be generated simultan-
generated at a time. eously.
181
181 - Multiple time-marks
184 TG 501 - Trigger output- 184 - Separate trigger
slaved to market
pulses of 1 and 0.1
output from 5 sec
sec; 10, 1, and 0.1
through 100 ns. One ms; 10 and 1 //s.
time-mark can be
generated at a time.
2901 TG 501 - Trigger output- 2901 - Separate trigger
slaved to marker pulses, from 5 sec
output from 5 sec to 0.1
n
s. Multiple
through 100 ns. time-marks can be
One time-mark can generated simultan-
be generated at
eously.
a time.
NOTE: All TM 500 generator outputs are short-proof. All TM 500 plug-in instruments require TM 500-Series Power Module.
R E V B, J U N 1978