Tektronix 1710J Series, Инструкция по эксплуатации

Страница: 11 / 252

Table of Contents
1710J-Series Waveform Monitors
vii
Figure 5–1: Simplified representation of a 1710J-Series Waveform
Monitor 5–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5–2: Simplified block diagram of the sync stripper 5–5 . . . . . . . . .
Figure 5–3: Simplified illustration of the bridge limiter circuit 5–8 . . . . .
Figure 5–4: Timing signals for 1-line and 2-line sweep 5–12 . . . . . . . . . . . .
Figure 5–5: Simplified representation of the pulse-width modulator
circuit 5–18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5–6: Z-Axis amplifier 5–21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–1: Remote connector for RGB 6–3 . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–2: Ten full cycles of calibrator signal between
timing marks 6–6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–3: Equipment hook-up for checking vertical gain 6–9 . . . . . . . .
Figure 6–4: Initial equipment setup to check Flat Response 6–12 . . . . . . . .
Figure 6–5: Connecting the RF bridge to the spectrum analyzer and
tracking generator 6–16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 7–1: RGB/YRGB parade display test connector 7–3 . . . . . . . . . . .
Figure 7–2: Adjustment locations for the Main and Power Supply
boards 7–5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 7–3: Segment of the Main board, showing the test points and
adjustment locations for the +11.8 V supplies 7–7 . . . . . . . . . . . . . . . .
Figure 7–4: Equipment setup to adjust 0.2 ms timing 7–8 . . . . . . . . . . . . .
Figure 7–5: Equipment setup for adjusting the calibrator
amplitude 7–10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 7–6: Equipment setup for adjusting Channel A input
compensation 7–12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 7–7: Adjusting for best flat response 7–13 . . . . . . . . . . . . . . . . . . . . .
Figure 8–1: Plug jumper locations and RGB compensation
adjustments 8–4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 8–2: REMOTE connector pin functions 8–5 . . . . . . . . . . . . . . . . . .
Figure 8–3: Common parts used to convert from +28 Vdc enable to
ground closure 8–6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 8–4: Bezel removal 8–10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 8–5: Rear panel securing screws 8–13 . . . . . . . . . . . . . . . . . . . . . . . .
Figure 8–6: Screws that hold the front panel circuit board (A2)
in place 8–14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 8–7: Screws holding the Main circuit board (A3) in place 8–15 . . .
Figure 8–8: Screws holding the power supply circuit board (A1)
in place 8–16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .