manualshive.com logo in svg

Tecmar Technologies 51000HT, Инструкция по установке и эксплуатации

Поделиться
Скачать
Tecmar Technologies 51000HT Скачать руководство пользователя страница 36

24

SQICUGM-EN2  Rev. A

About SCSI Bus Termination

This section provides a brief tutorial about how to configure a system to provide 
proper termination on a SCSI bus.

A single SCSI host adapter can support up to six other SCSI devices. The devices 
can be linked directly to the host adapter or, more commonly, linked to each other 
in a daisy chain. Figure 5 shows two examples of SCSI bus configurations: 1) a 
host adapter with a single (internal) SCSI device and 2) a host adapter with four 
other SCSI devices linked serially. The line the devices share is the SCSI bus.

SCSI is a very powerful I/O protocol that handles large amounts of data very 
quickly. Disturbances on the SCSI bus such as signal distortion, or echo, can 
cause problems. Terminating the SCSI bus filters out signal distortion. It is, 
therefore, very important that the bus be properly terminated.

When a SCSI bus is properly terminated, the first device and the last device on 
the SCSI bus are terminated, and termination is removed or disabled on any 
device in between as shown in Figure 5.

In a QIC drive, SCSI termination is either enabled or disabled by installing or 
removing three resistor packs. Power to the terminators is supplied by one SCSI 
terminator power jumper.

Internal QIC drives are shipped with termination enabled. To disable or remove 
termination on an internal model, refer to “Setting SCSI ID and Termination 
Power” in this appendix.

External QIC drives are terminated on the rear panel of the unit.

qicaa.fm  Page 24  Wednesday, April 23, 1997  6:07 PM

Содержание 51000HT















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды