Technische Alternative CAN-EZ3 Скачать руководство пользователя страница 65

Страница: 65 / 96

CAN analogue inputs

Up to 64 CAN analogue inputs can be programmed. They are defined by specifying the transmission

node number and the number of the transmission node's CAN output.

Node number

After the node number of the

transmission node

is entered, the other settings can be specified. The

number of a CAN analogue output is taken from the device with that node number and applied here.

Example:

On CAN analogue

input 1,

the output number applied is that of CAN analogue

output 1

from

the device with node number 2.

Designation

Every CAN input can be given its own designation. The designation can be selected from various des

ignation groups or can be user defined, as for the other controller inputs.

Содержание CAN-EZ3

































































































Результаты поиска

Содержание CAN-EZ3

Отзывы:

Похожие инструкции для CAN-EZ3

Бренды по названию

Популярные бренды

Technische Alternative CAN-EZ3, Общая информация, Установка и подключение, Основные функции

Результаты поиска

Содержание CAN-EZ3

Отзывы:

Похожие инструкции для CAN-EZ3

Бренды по названию

Популярные бренды