Technische Alternative CAN-EZ3 Скачать руководство пользователя страница 37

Страница: 37 / 96

Date-specific memory

View on display

View in TAPPS2

The arithmetic operation is performed according to the following formula:

• The first field

Function

can remain empty, in which case it has no effect on the arithmetic oper

ation. In this field, a function can be selected which will be applied to the result of the arithme

tic calculation that follows:

• Absolute value

• Square root

sqrt

• Trigonometric functions

sin

cos

tan

• Inverse trigonometric functions

arcsin

arccos

arctan

• Hyperbolic functions

sinh

cosh

tanh

• Exponential function e

exp

• Natural and common logarithms

and

log

• The fields marked Operator 1 - 3 are for selecting the arithmetic operation::

• Addition

• Subtraction

–

• Multiplication

• Division

• Modulo

(remainder from a division)

• Exponentiation

• The brackets must be observed in accordance with mathematical rules.
• In the "

differential

" version, these mathematical calculations therefore allow the daily, monthly

and annual performance factors to be calculated by dividing the heat amount (thermal energy)

by electrical energy and stored on a daily, monthly and annual basis.

Daily values
Monthly values
Yearly values

The stored values are displayed by selecting these buttons

Delete history

Selecting this button deletes the stored values after a confirmation

prompt.

Output variables

Previous day value

Display of the stored previous day value

Содержание CAN-EZ3

































































































Результаты поиска

Содержание CAN-EZ3

Отзывы:

Бренды по названию

Популярные бренды

Technische Alternative CAN-EZ3, Общая информация, Установка и подключение, Основные функции

Результаты поиска

Содержание CAN-EZ3

Отзывы:

Бренды по названию

Популярные бренды