Technische Alternative CAN-EZ3 Скачать руководство пользователя страница 43

Страница: 43 / 96

Basics

This section is designed as a guide to programming directly on the device, but also provides impor

tant information about the elements required for programming with the TAPPS 2 programming soft

ware (functions, inputs and outputs, etc.).
Programming with TAPPS2 is always recommended. It enables the programmer to draw (= program)

all program operations in the form of a graphical flow chart and to define parameters for them
accordingly.
Nevertheless it is important to know how to use the "programming mechanisms" on the device itself

in order to be able to make changes on site.

Device overview

The display

(1)

on the front shows information about sensor measurements, menu position, param

eters and such.
The wheel

(2)

to the right of the menu serves to navigate through menus. Twisting it clockwise nav

igates downwards in a menu, twisting it counter-clockwise navigates upwards.
Pushing the wheel

(2)

down opens the currently selected menu/enables changing the currently se

lected value/parameter. (= Enter button)
Pushing the button

(3)

left of the wheel leaves the current menu. (= Back button)

Pushing the „Enter button“ or the „Back button“ is related to the value/menu point that‘s framed.
The

"Status"

LED

(4)

above right of the rotary dial provides information on the status of the device.

Green flashing means the energy meter is starting up. A continuous green light shows normal oper

ation. Orange means there is a "message", for example concerning a collector over-temperature

shutdown. Red means there is a "fault", such as a DL sensor failure.
At a short push of the Reset button

(5)

, the device reboots. To carry out a total reset of the device,

push the button until the status LED

(4)

stops rapidly flashing orange and begins slowly flashing in

red.

Содержание CAN-EZ3

































































































Результаты поиска

Содержание CAN-EZ3

Отзывы:

Похожие инструкции для CAN-EZ3

Бренды по названию

Популярные бренды

Technische Alternative CAN-EZ3, Общая информация, Установка и подключение, Основные функции

Результаты поиска

Содержание CAN-EZ3

Отзывы:

Похожие инструкции для CAN-EZ3

Бренды по названию

Популярные бренды