_ 7 _
Anything previously recorded on the tape
will automatically be erased when you
make a new recording on it. It can also be
erased by "recording" on it with the REC
LEVEL control set to "
‹
".
1. Press the POWER switch to ON.
2. Load the pre-recorded cassette into
TAPE I and a recordable cassette into
TAPE II.
3. Fully rewind both cassettes so their
tapes are taken up on their left reels.
4. Set the REV MODE switch to the desired
position.
“
: Dubbing will be performed for one
side only.
π
: Dubbing will be stopped after both
sides have been dubbed.
5. Set both decks to the
∏
direction.
6. Press the DUB START HIGH or NORMAL
button to start dubbing. The indicator
corresponding to the button pressed will
light.
NORMAL:
Dubbing is performed at nor-
mal speed.
HIGH:
Dubbing is performed at
twice normal speed.
7. The peak level meter indicates the TAPE
I signal levels; the recording levels of
TAPE II will be set automatically (at the
same levels as TAPE I).
8. After dubbing is completed, both decks
stop automatically, according to the set-
ting of the REV MODE button.
9. To stop dubbing, press either of the
∑
STOP buttons.
Erasing
Dubbing (Copying from TAPE I to
TAPE II)
Recording from a stereo system:
1. Press the POWER switch to ON.
2. If you want to make a bi-directional
recording, set the REV MODE switch to
the
π
position.
3. Load a recordable cassette in TAPE II.
●
Check that the safety tabs on the spine
of the cassette are in place. If they have
been broken off, block the holes with
adhesive tape.
4. Select the desired DOLBY NR system.
5. Press the RECORD button and the deck
enters the record-pause mode. ( REC
and
ƒ
indicators light.)
6. Adjust the recording level with the REC
LEVEL control so that the loudest sound
to be recorded just makes the meters
briefly reach around the "0 dB" point (for
Normal or Chrome tapes) or the "+3 dB"
point (for Metal tapes).
7. Press the PAUSE button again to start
recording.
●
To stop recording temporarily, press the
PAUSE button. To restart the tape, press
it again.
●
To stop recording, press the
∑
STOP
button.
Recording with TAPE II
●
Automatic spacing operation for 4-sec-
ond blanks (during recording)
Press the REC MUTE button during
recording. The tape movement continues
and a blank space of about 4 seconds is
recorded (the RECORD indicator blinks).
The deck then enters the record-pause
mode automatically (both the RECORD
and PAUSE indicators light).
To restart recording, press the PAUSE
button (the PAUSE indicator goes off).
●
Automatic spacing operation for 4-sec-
ond blanks (during record-pause)
In the record-pause mode, pressing the
REC MUTE button will initiate the above
record-muting operation automatically.
The deck then returns to the record-
pause mode.
●
For a blank of more than 4 seconds
During recording, hold the REC MUTE
button depressed for longer than 4 sec-
onds. A blank space will be left as long as
the button is pressed. Release the button
to enter the record-pause mode. To
restart recording, press the PAUSE but-
ton.
●
For a blank of less than 4 seconds
After pressing the REC MUTE button dur-
ing recording, press the PAUSE button
before 4 seconds has elapsed. The deck
will stop and enter the record-pause
mode at the point at which the PAUSE
button is pressed. To restart recording,
press the PAUSE button again.
Note:
●
During record muting operation (while
the RECORD indicator is blinking), press-
ing the REC MUTE button again will
release the record muting operation and
recording will restart without stopping
the tape.
Record Muting Operation
To dub the entire recorded section of a
pre-recorded cassette
CAUTION:
Recording pre-recorded tapes, records,
or other published or broadcast materi-
al may infringe copyright laws. Check
these laws before recording.
