PAQ
65D
PAQ
B-254
・All specifications are subject to change without notice.
3.1.4 Standard PAQ65D48-2518 model
(i) 2.5V: Output Trim Up
(ii) 1.8V: Output Trim Up
(iii) 2.5V: Output Trim Down
(iv) 1.8V: Output Trim Down
Trim Up ΔVo（%）
1
2
3
4
5
6
7
8
9
10
Radj1-up（kΩ）
205
103
69.4
52.5
42.4
35.6
30.8
27.2
24.4
22.1
Trim Down ΔVo（%）
−1
−2
−3
−4
−5
−6
−7
−8
−9
−10
Radj1-down（kΩ）
94.2
46.5
30.6
22.7
17.9
14.7
12.5
10.7
9.42
8.36
Trim Up ΔVo（%）
1
2
3
4
5
6
7
8
9
10
Radj2-up（kΩ）
120
60.3
40.5
30.6
24.7
20.8
17.9
15.8
14.2
12.8
Trim Down ΔVo（%）
−1
−2
−3
−4
−5
−6
−7
−8
−9
−10
Radj2-down（kΩ）
94.2
46.5
30.6
22.7
17.9
14.7
12.5
10.7
9.42
8.36
3.2.1 PAQ65D48-5033/C option model
(i) Common Output Trim Up
(ii) Common Output Trim Down
Trim Up ΔVo（%）
1
2
3
4
5
6
7
8
9
10
Radj-up（kΩ）
50.0
23.0
14.0
9.2
6.4
4.5
3.1
2.1
1.3
0.0
Trim Down ΔVo（%）
−1
−2
−3
−4
−5
−6
−7
−8
−9
−10
Radj-down（kΩ）
67.0
30.0
17.0
11.0
7.8
5.4
3.7
2.4
1.4
0.0
3.2.2 PAQ65D48-3325/C option model
(i) Common Output Trim Up
(ii) Common Output Trim Down
Trim Up ΔVo（%）
1
2
3
4
5
6
7
8
9
10
Radj-up（kΩ）
46.0
20.4
12.1
7.9
5.2
3.5
2.2
1.3
0.61
0.0
Trim Down ΔVo（%）
−1
−2
−3
−4
−5
−6
−7
−8
−9
−10
Radj-down（kΩ）
56.9
25.0
13.8
8.8
5.8
3.8
2.3
1.3
0.43
0.0
3.2.3 PAQ65D48-3318/C option model
(i) Common Output Trim Up
(ii) Common Output Trim Down
Trim Up ΔVo（%）
1
2
3
4
5
6
7
8
9
10
Radj-up（kΩ）
13.5
6.2
3.8
2.6
1.9
1.4
1.05
0.79
0.59
0.43
Trim Down ΔVo（%）
−1
−2
−3
−4
−5
−6
−7
−8
−9
−10
Radj-down（kΩ）
15.2
6.9
4.2
2.8
1.98
1.43
1.03
0.74
0.51
0.33
3.2.4 PAQ65D48-2518/C option model
(i) Common Output Trim Up
(ii) Common Output Trim Down
Trim Up ΔVo (% )
1
2
3
4
5
6
7
8
9
10
Radj-up（kΩ）
13.5
6.2
3.8
2.6
1.9
1.4
1.05
0.79
0.59
0.43
Trim Down ΔVo (% )
−1
−2
−3
−4
−5
−6
−7
−8
−9
−10
Radj-down（kΩ）
15.2
6.9
4.2
2.8
1.98
1.43
1.03
0.74
0.51
0.33
4 Maximum Ripple and Noise
The standard measurement for output ripple and noise is
as shown in Fig.4-1. Connect a 22μF ceramic capacitor
for each output (C2 and C3) at 50mm away from the out-
put terminal. Use a normal probe with 20MHz bandwidth
scope to measure the ripple and noise at the position of
C2 and C3. Upon measurement of the ripple voltage,
make sure that the oscilloscope probe leads are not too
long.
Take note that output ripple voltage and output spike noise
may vary depending on PCB wiring design. Generally, out-
put ripple voltage and output spike noise can be reduced
by increasing value of external capacitor.
50mm
MEASUREMENT POINT FOR
RIPPLE & NOISE (20MHz)
TRM1
TRM2
Vo1
Vo2
GND
−
＋
−
＋
LOAD
LOAD
C2
C3
Fig.4-1: Measurement method for ripple and noise
Содержание PAQ100S48-1R2
Страница 36: ...B 260...
