tayco Halifax Скачать руководство пользователя страница 48

Страница: 48 / 55

Metal Storage, for Under Hutch

Tools & Hardware Needed

8540-0545

Drill

Robertson # 2

Tape Measure

#10 X 11/16" Oval

Head Screw (5X)

Align the edges of metal

storage 1 with the edges of

bottom laminate of the

overhead storage. Make

sure the edges of the metal

storage and edges of bottom

laminate of the overhead

storage are flush, (Figure 1).

Attach the Metal Storage in

the underside of Overhead

Storage/Hutch using (5)

#10

x 11/16" Oval Head Screws.

Align the edges of the metal

storage 2 with the edge of

the metal storage 1 and the

front edge of bottom

laminate of the overhead

storage.

Repeat Step 2.

METAL STORAGE 1
METAL STORAGE 2
#10 x 11/16” OVAL HEAD SCREW
OVERHEAD STORAGE/HUTCH

Flush edge of metal storage

with the edge of the laminate

Flush edge of metal storage

with the edge of the laminate

and metal storage

Figure 1

Figure 2

May 2023

halifax 48

Содержание Halifax
























































Результаты поиска

Содержание Halifax

Отзывы:

Похожие инструкции для Halifax

Бренды по названию

Популярные бренды

tayco Halifax, Руководство по установке

Результаты поиска

Содержание Halifax

Отзывы:

Похожие инструкции для Halifax

Бренды по названию

Популярные бренды