tayco Halifax Скачать руководство пользователя страница 21

Страница: 21 / 55

Figure 10

Figure 11

Low Credenza Mounted Desk, A-Leg w/ Short Gable

Tools & Hardware Needed

8540-0545

MENDPLATE-BLK

Drill

Robertson # 2

Tape Measure

Torpedo Level

#10 x 11/16", Oval

Head Screw

Mending Plate

3.00 "

Note:

Lay down wires/cables

before installing the surface.

11.

Fish wires and cables through

desk support metal box,

(Figure 10).

12.

Position desk so it rests on

the desk support box; level

the desk by adjusting the

glides.

NOTE:

Make sure the outer

corner of short gable and

back corner of low credenza

are flush

13.

Secure the desk by attaching

the mending plates with

provided #10 x 11/16, Oval

Head Screws, (Figure 11).

Continued on the next page >>

LOW CREDENZA STORAGE
DESK SUPPORT BOX
WIRES/CABLES
MENDING PLATE
#10 X 11/16" OVAL HEAD SCREW

May 2023

halifax 21

Содержание Halifax
























































Результаты поиска

Содержание Halifax

Отзывы:

Похожие инструкции для Halifax

Бренды по названию

Популярные бренды

tayco Halifax, Руководство по установке

Результаты поиска

Содержание Halifax

Отзывы:

Похожие инструкции для Halifax

Бренды по названию

Популярные бренды